Zero Targets Optimized for Red Dot Style Optics (Aimpoint, EOTech, etc...)

Tactical Gear Optics & Mounts
41

Very nice. Great job!

Thanks

42

Thanks, for the updated targets. Great job.

43

Thanks for these.

44

How do these work with sights at 1/3 co-witness height? I know they work with standard height sights, but I didn’t see if 1/3 co-witness threw it off at all.

45

I’ve used the 25 yard adjusted targets with both a 1/3 co-witness Aimpoint and with an EOTech with an absolute co-witness when testing these. I did not notice anything that would warrant a different target for each optic co-witness. The difference is so minute, I don’t think you’d notice it. However, this is why I also say the adjusted target will get you close (and most of the time dead on in my experience), but you should always confirm your zero at the actual distance.

If you’re using the 50 yard target at 50 yards, different co-witness is a non-issue.

46

Finally got a chance to use these today zeroing a new DD upper. Eotech EXPS2-0, lower 1/3 cowitness FWIW. The targets worked perfectly. Started at 25yds, dialing it in for the 50yd zero. The first group was luckily on the target, and the adjustment grid was dead on the money. In 6 shots I was zeroed on the 25yd target.

Then I set up the 50yd target at 50yd and shot another group. I was one click high, which I attribute mostly to the target being a few yards shy of 50.

All said and done I was zeroed on the 25yd target and verified on the 50yd target in 12 rounds.

Great job on these, thanks again.

47

I am going to try this on Sunday while using my PRO for the very first time with the 50yd target?

Anyone have an idea of roughly how many clicks it takes after being zeroed at 50 to reach 100yd?

Thanks, I honestly have no idea.

48

Most likely around three clicks down depending on set-up and ammunition. If zeroed at 50 yards, your POI at 100 yards will be about 1.5" above POA.

49

Yeah, I ended up finding out that it was 3-4 clicks when I dialed it in today.

I will just need to memorize the come-ups for the various distances, and I’ll be good.

50

Added a version of the 50 Yard target without the large assisting ring to the original post.

51

Thanks so much for making these available. I printed a few of these off yesterday and headed out to sight in a new Eotech EXPS3-0.

I started at 25 yards to make sure I was on paper. I didn’t use the adjusted 25 yard target. I just sighted in a little low. Then I moved back to 50 yards (measured with my laser range finder) and fine tuned. These made it very easy. Being able to see the ring on the paper and center it within the ring of the Eotech’s reticle was a big help as well. I didn’t keep a count of how many rounds it took to zero, but it wasn’t many.

I also found them extremely helpful for sighting in my MBUS at 50 yards. Again the large ring on the target was very helpful.

The rifle used has a 16" lightweight barrel and I was shooting Federal Lake City XM855.

52

I couldn’t agree more. These are fantastic. Thanks again!

53

Thank you so much for the targets. You are a good man!

54

Thanks for the targets. I was able to zero my Aimpoint Pro with 12 rounds yesterday. Your targets made it ridiculously simple.

55

Your targets are amazing and make teaching cops how to zero so much easier.

Thanks for sharing!!!

56

Thanks a lot.

57

Would love to see an AK version. Thanks for sharing your work.

58

Thanks for sharing the targets :smiley:

59

Thank you, These are great!

60

These targets helped me zero two aimpoint comp m2’s and an eotech xps today in about twenty minutes. Left me plenty of range time for the new sbr :slight_smile: