setting CRS on Vortex pst scope

Recently purchased a Vortex PST 2.5-10 x 32 (mrad version), installed on Vortex branded 30mm cantileverd mount.
I can’t remember who manufactured the upper, (spare parts bin), the Barrel is a Faxon 18 inch gunner, with Midwest industries free float/proprietery barrel nut
My issue in order to obtain this at 100 yards using my hand loads Hornady 62gr fmjbt, winchester primer, 25.5 grains cfe223, range brass[](http://s226.photobucket.com/user/fallsafe/media/fullsizeoutput_291.jpeg.html)
I must Dial up to this
That leaves me with approx 14 mil left to dial up (2.5) turns
I used 9 shims to set the CRS is that normal?
I installed the barrel using mag pull vise block and the correct wrenches and torque per manufacture, could i have misaligned it downward some how?

I have sent Vortex an email, but its Sunday holiday weekend so i thought I’d ask any PST users for advice

Is the mount a 0 MOA cant?

I used a 20 MOA rail and I think I used 5 shims maybe.

Let’s see pics from the side with the whole optic and rail in view.

Could it be possible you have a 20 MOA rail on backwards?

^^^ I know that sounds silly but it happens.

Sent from my iPhone using Tapatalk

0 MOA Cant Pictures shortly

Something perhaps with the way the barrel is fastened-- like receiver face way out or barrel extension flange that is not parallel or some debris in there during assembly. Could be many other things too but yeah that is not as one would like to see it.

Looking again-- and re reading-- and not familiar with the PST, but-- only 14 mils of up, sounds like not so terribly little, 'specially in 5.56.

I was thinking the same thing. 14 mils will get you a long way.

Sent from my iPhone using Tapatalk

Just thought it was strange I had to use 1/2 my available vertical adjust to get that a 100 yards,
Heck at 50 yard with the turret dialed all the way down i was hitting dirt, had to dial up just shy of turret photo to hit the diamond before i pushed it out to 100 yards, temps started dropping in the low 30 s so i packed up and went home

Maybe I’m just over thinking this.

Thanks for the help

Interesting. I only had to dial about 0.8 mil or so to zero mine at 200m (similar setup, but with a LaRue mount). I didn’t even shim the turrets (couldn’t find the shims, dammit), just reset 'em to zero with the set screws once I got her centered up. If I need to adjust past 5 mils, hopefully I can remember how many elevation turns I put in…

Honestly though, I think you’re fine. For 5.56 you shouldn’t need more than 7-8 mils of elevation adjust, unless you’re shooting beyond 700m, in which case you’ve still got 6-7 mils of elevation adjustment to play with (maybe another 300m or so?). If it really bothers you, I’d look at your mount and rings first. Make sure nothing needs lapping, bedding etc. Try a different mount if it’s not too much of a PITA- that one could be off by a couple of mils.

Was the scope brand new when you mounted it?

Remove shims and turn elevation turret all the way down and then back up and again. Split the number you get in half and find your mechanical zero. The turrets may have been slipped and not reset.

Not a bad idea, but IIRC, this scope is set so that zero isn’t in the mechanical center of the adjustment range (e.g. you get a lot more up-adjust than down-adjust.)

I could be wrong. :confused:

Just checked my ballistic calculator with a guesstimate for muzzle velocity on some 77gr SMKs at around 2800fps. At 1000yds it calls for 12.2 mils so you should be fine with 14 mils of dial up.

I’m using the same scope on a similar build but didn’t have to dial as much for zero (using a Warne SKEL mount). After initially boresighting it the best I could, I zeroed it with 69gr Federal GMM and I think I used 6 shims. Never has a problem and have had that gun out to about 725 without issue.

I was always surprised that the Burris Signature rings did not get more attention: the ones where rings have plastic inserts that are spherical on the outside. You can get them in, as I recall, plus .010 and .020, and minus .010 and .020, so pretty much no matter what you can raise or lower the front and/or rear of the scope. As the inserts are spherical where they nestle in the rings, as you tighten things up you can’t help but have perfect ring alignment. I used them on an old Redfield scope that had been dropped, the tube was bent and you could not zero it. All I had to do was align the scope “off” using these rings and I was back in biz.

They just never seemed to pass “tactical muster”. http://www.burrisoptics.com/signature-rings

Heard back from Vortex,
All is well, That Dial up to zero this particular rifle at 100 yards is not unusual so my CRS goes there,
Thanks for all the advice

I recently changed to a LaRue lt158-30 vfz scope mount for this project it has a 10 moa down angle.

My previous Vortex mount had zero.

To rezero my Vortex scope i’m pulling the shims, the Scope is in mils what would be an approximate start, googling I think I need to dial down approx. 3 mils for a starting point, does that sound about right.