Realistic cost for reloading?

I think my next step in shooting is to start reloading. I shoot 1911’s a lot, and the cost of 45acp sometimes keeps me home instead of heading out to the range.

For those of you who reload, what do you think are realistic costs to get into the proper equipment to begin reloading? I have done some research and can see that the “all included” kits are well rounded, but there seems to be a lot of “other” items that are also needed from tumblers, to scales etc.

I have been looking at the Dillion Square Deal. Right now I don’t shoot enough of any other caliber to justify getting setup to reload them as well. And I can buy 9mm reloads here (local guy supplies all the PD’s in the area) for less than I can assemble the parts.

So for now, I am looking just at 45acp. I would love to shoot around 500 rounds per month or so.

Thanks in advance-

In a years time… at 500 rounds per month… you could save about 1800 dollars in ammo costs, Cousin.

Without trying very hard… you can get a lb of Hp-38 for $17.99, large pistol primers for $17.99ish, and 1000 23 grain plated berrys bullets for $142 delivered.

That = $0.174 per round. At Cabela’s 230 fmjs are about $23.99 per 50… or $0.48 per round. A difference of $0.30 per round.

Multiply your savings by 500 rounds and by 12 months and you’re at 1800 dollars in a year. You can buy some NICE reloading stuff for less than 1800 bucks. :wink:

I have had a Dillon SQDB since 1995. I bought it used at a gun-show at the urging of a shooting buddy. Best investment I ever made in my shooting. It has broken from time to time since I got it. Just call Dillon; me: my XXX on my SQDB broke. Dillon: what’s your address so we can send you a new one? Look around locally for the best prices on primers and powder. Look on line for bullets. Pick up brass at the range.
Bullets:
Precision Delta
Zero
Montana Gold
Berrys
Some of the bullets I’ve used.

Best,
19852

While I wish I could still find primers for what Markm can (around my area they are 26 to 30 bucks per K), you still save a lot if you shoot frequently. I figure it costs me half (or slightly less, depending on caliber) of store prices on pistol ammo.

I shoot at least about 1K/month, so this saves me quite a bit. The case cleaners, scales, etc. are relatively cheap, so your initial outlay is not too bad. Get a good caliper for measuring case length, diameter, etc. Shooting as much as you describe, you should recoup your costs in a few months or so.

I will warn you though, it is addictive, especially if you start in with precision/bullseye shooting and you start “tuning” loads.

Yeah… I buy them in bulk from Wideners… I haven’t checked my local prices lately. But even at 26 per hundred, there’s still plenty of room for savings.

The Lee Classic Turret is a very good starting press for the money and it will easily fill your needs. Kempf Gun Shop sells it as a kit with two very needed upgrades – the Safety Prime System and the upgraded disc powder measure:

Kempfgunshop.com

Bear in mind that in addition to buying the press, you’ll likely also need a bench, brass tumbler, cleaning media, polish, brass lubrication (Hornady One-Shot), calipers, scale and perhaps a few other accessories such as a bullet puller. That will be your start-up costs - your additional money goes into bullets, powder and primers each time you load.

Since brass is free to me, I can load 9mm with 124gr jacketed bullets for about $11 per 100. That’s more than a 50% savings from factory ammo. If I started shooting lead I’d save even more. Taking a SWAG at .45…

Primers - $30/1000 (3 cents per shot)
Bullets (230gr FMJ) - $119/1000 (11.9 cents per shot)
Powder - $20 per pound (with say WSF under 230gr FMJ it’s about 1.7 cents per shot)
Brass – assume free from range

Rounding up you’d be at about $17 per 100 rounds. If you shoot lead you’d likely be at about $13/100 or less. From what I can gather factory .45 seems to be selling for around $34/100 so again you’d save at least 50%.

One of the biggest benefits to loading our own ammo though is being in control of what you’re shooting. With a little patience and some research you’ll be cranking out ammo that burns cleaner and shoots more accurately than any factory plinking fodder on the market. Personally, I load purely for economics so I stick with a proven load once I find one but many loaders make a hobby out of working up pet loads.

Good luck.

Others have indicated your potential cost savings.

I would start with a quality single-stage press, don’t worry about the fact that it’s slower. High quality single-stagers that don’t cost a fortune are made by many companies. A few examples of ss presses, prices all from midwayusa.com: RCBS (Rock Chucker: $129), Hornady (Lock n Load: $134), Forster (Single stage coax: $234), Redding (Boss: $124). With a good ss press, a digital scale, dies, and a few other odds and ends, you could definitely get the basic hardware you need to get started for around $500, excluding of course the actual reloading components.

For components, don’t forget to check out Powder Valley. They have great prices, selection, and service. I have no connection with them, just like their store.

http://www.powdervalleyinc.com/

I’d suggest going the more simple route to begin with at least until you are comfortable with the whole process.

While I completely endorse the Dillon idea, there are many small things to keep track of with a progressive setup.

A good single stage press will both let you jump right into loading and soften the learning curve as you will learn to fine tune each step.

Once you are comfortable the progressive setup really is the only way to go for high round count pistol shooting. If you enjoy it as much as many do, you will begin loading several other calibers and the single stage will serve you well for more precision work.

This is true. But one can always run a single piece of brass through a progressive at a time. That way he can focus on one process each cycle of the press and not miss a thing.

I started out on a 550b and never had any issues that I wouldn’t have had on a single stage. In fact… if you took away my 550 and left me with my single stage… I’d have a harder time learing how to make ammo than I did learning the 550b.

I have a Dillion SDB on my bench dedicated to .45ACP that was given to me several years ago. I learned on that press and it has produced many thousand rounds without issue. I also have a RCBS press (also a progressive) on the other bench I use for rifle and other pistol calibers.

Sorry, I don’t subscribe to the theory of you gotta start out on a single stage then move up… but hey, what do I know?? :wink:

Good luck,

I started loading .45 ACP on a Dillon 550B and way more than paid for it in savings in less than a year. I buy Wolf LP primers and Winchester W231 or Hodgdon HP38 from Powder Valley. I shoot Missouri Bullet’s 200gr IDP #1. I couldn’t decide between the SDB and 550 but chose the 550 to be able to load rifle later. I’ve just started loading .223. There is great info. on this site and at Brianenos.com. I don’t know if I’ve saved money because I shoot more for the same money. Enjoy!

that^^

Calipers, Scale, tumbler, sifter, books, Work bench to mount press on?
add all those together with the cost of your press and fill in the blanks

http://10xshooters.com/calculators/Handgun_Reloading_Cost_Calculator.htm

Thanks everyone, this is the kind of stuff I was really looking for. I have been saving my brass since I started shooting (my dad taught me early on) so I am sitting on literally 1000’s of empties.

I appreciate all the help. I am trying to decide if the 550b is a better option for me as I am a dedicated buy once cry once shopper. I can see this spilling over into reloading .308 down the road, but my access to a long range right now makes it prohibitive.

Square Deal hands down, my press specifically for 45 acp paid for itself in 2 weeks, as I detesting tinkering or changing things, I have a second one for 9mm or 40 S&W so I don’t have to swap over to small pistol primer setup.

When I decide to reload for 223 it will be a 650 with case feeder and all the goodies.

I bought a Square Deal for my first press and promptly sold it. It’s a very small and cramped press that allows for only straight-walled pistol cases. IMHO you’ll be better off with either Lee’s Classic Turret or the Dillon 550B – especially if you think you’ll eventually start loading rifle. Since the 550B is a manual indexing press and you can remove the indexing rod from the LCT, both presses can be operated like a single stage if you want to take things slow.

I have the LCT and I shoot about 125 rounds a week of 9mm and maybe 100 rounds a month of .38 special. It more than meets my needs. If I’m in a hurry I can actually load about 300 rounds per hour although I typically take my time and (safely) load at a rate of about 200-225 rounds per hour.

The 550B’s production rate is of course even faster. If you’re a buy once, cry once kinda person, buy that press instead. It’s a very versatile press and would probably more than meet the needs of about 99% of the shooters out there.

The biggest cost of reloading is TIME, as long as you dont buy a $300 trimmer reloading is VERY cheap.

I just started loading 38 special and the cost to load 500 rounds was $65, factory ammo at local prices would have been a minimum of $180!

It depends on the caliber and what components you are willing to use. If you are fine with shooting lead projectiles, you can make plinking ammo cheaper then you can buy just the jacketed projectiles.

If you shoot the gun games or even moderately serious volume, a single stage won’t get you to the dance in a timely manner. Nevertheless, a single stage press, especially a quality turret press, is very handy to have on the loading bench.

Reloading .45 ACP is as simple as it gets - a Dillon 550B is much more versatile than a SDB, but either would be an excellent choice for a first loader.

Something more complex like the Dillon 650 might be a bridge to far for a first timer. Simple (like the 550) could even be faster for some people.

I load all large primer cases (.45, .308, .30-06 .243, 6.5x55, 8mm, etc.) on a 650 - But all bottle neck rifle cases are first sized on a turret press. All small primer cases - .223 (and .40 S&W if I feel the need) are loaded on a 1050. Both machines are > 20 years old.

I started out loading .45 ACP on a Dillon SDB a couple years ago. Total investment was approximately $700 for the press and accessories, excluding components. 230g FMJ cost roughly $17 per 100 to load, but lead bullets for a 1911 could be loaded for less. My press paid for itself very quickly. Actually, you only need to recoup roughly 20% to 30% of the costs of the press because it retains most of its value on the second-hand press market.

One thing seldom mentioned to newbies is to be realistic in how many rounds you expect to load. Since ammo can be reloaded at half its retail cost, many of us shoot twice as much. Personally, I put 1,800 rounds through a new pistol last month, and this would have been a huge time investment on a slow press.

This is where starting out on a single stage would make you nuts if you’re a results oriented person.

I started out with a Lee Classic Turret press, and with practice I was able to produce about 200 rounds per hour. I usually shoot about 300 rounds a week of pistol, so that wasn’t too bad.

Lately, I tend to load up a bunch of ammo at once, and then not reload anything for a while, and for that reason I am considering a Dillon just to cut the time spent reloading down. I will probably start shooting more as well.