Not Thanksgiving but i seem to have gotten a Turkey

Good afternoon
I hope someone can help me with a problem i am having? Yesterday at the gun show in Kansas City, Mo. I stopped by the CMMG table and ended up leaving with a new upper. It was supposed to be new so this morning i cleaned and lubed it and took it out with some known good ammo [green tip 62g.] Anyway i seem to have a fairly expensive single shot. When i fire, the expended round ends up with the new round jammed against it from underneath [kinda like a double feed except one rd. is fired] you then have to remove the mag and reach in and dislodge the fired and unfired rds. After several attempts i loaded just one round in a mag and fired it.Each time the bolt locked back but twice the fired round was not fully ejected and the other 2 times it barely fell out of the ejection port.
Can someone help?
Thank you…Macon

Was the bolt carrier group new or used? It could possibly be your ejector is weak. What type of buffer and spring are you using? Can you be more specific about the ammp that you are using?

Sir
The bolt carrier group looks brand new and as i mentioned i bought it as new. The ammo was 62g. FMJ in LC brass , 25.9 g. of WCC 844 with a Win. SR primer.This functions great in my M-4 and both my buddies M-4’s. The buffer and spring are what came with my M-4 lower when i ordered it from Del-Ton a couple of years ago. Again it has worked fine with my other upper. I was wondering about the extractor myself? Thanks again for any help.
Macon

There may be an extractor issue, but I am curious about the comments concerning the ejection problems. Also, I wouldn’t use reloads for any type of function testing regardless of its’ past performance.

I should have asked is this a rifle or carbine upper? Make sure that your gas key is staked properly, and see if you have the correct extractor spring and insert.

Check the extractor and make sure it’s in good shape. Make sure it has the right spring and insert. If you don’t find any problems then pull an extractor from another rifle and try it out.
Next time you take it out try some good FACTORY ammunition. I have seen this happen before where hand loads work in some guns but not in one. I have been rolling my own for 20+ years and still use factory ammo in new guns.

Also will it hand cycle?

Iraqgunz
I was thinking the “ejection problems” might be caused by the extractor being defective and releasing the round before it gets to the ejection point? Also…it is a carbine upper. As to the correct extractor spring and insert…i’m afraid i wouldn’t know the correct ones if they bit me on the ass?

Iraqgunz and 5pins…
Why would you not use reloads to test with? These are what i plan to shoot with? I full length resize,tumble,trim,ect and have loaded for almost 35 years. Not saying you are wrong…just wondering?

Anyhow…thanks…Macon

You should have an extractor spring that is usually 5 coils and contains a black insert. They are designed for the carbine extractor. Only a handful of manufacturers actually use the correct one. You can also add an O-ring to the extractor to increase tension.

By using quality factory ammunition you can rule out any errors that may have been made on your part. Also, there are times when certain types of ammunition and AR’s aren’t compatible and one has to sort it out.

Iraqgunz
I sent you an e-mail thru this site concerning my “turkey”.
Thanks…Macon

Have you tried a selective parts interchange with your other upper?
I would swap the bolts and see if that made any difference.
If so, the trouble-shooting on the problem bolt can begin.

Failure2Stop
Yessir,tried that today.Swapped my whole BCG…the new carbine ran fine. Then swapped just the bolt, again the carbine ran fine. Got to really checking the bolt out and discovered it seems to be a bolt for a 6.8 rather than for a 5.56. At least the bolt face opening measures .4265" on the one that does not work and .379" on my good one from my M-4. So…it looks like they put it together using the wrong bolt and i need a different one [ofcourse everyone seems to be out of them now.].
Macon Due

Here is a discussion on the JP bolt that Sinclair has. As far as I can tell they are the only ones to have any bolts stock.

https://www.m4carbine.net/showthread.php?t=26150

http://www.sinclairintl.com/cgi-bin/category.cgi?category=search&item=14-7650&type=store

I have LMT enhanced bolts in stock. Rather pricy at $155.

If you bought it from CMMG I would call them and tell them your problem. Im sure they will swap your bolt out for you.

KBAR
I did, e-mailed 3 times and called and left messages. They did finally get back to me. Seemed like they want to make it right. Just too bad you can’t buy something and have the right bolt installed in it when purchased? Anyhow i’ll see how it goes after i get it back?
Thanks…Macon

They are good people but , like everyone else in the industry now, they are totally overwhelmed by market demand. Jeff told me they were 15000 rifles behind in orders and their phones are ringing off the hooks…