Member Survey: "Which AR STOCK do you use and why?" Thread!

Be thorough, be specific. “I like the Magpul UBR” isn’t what we’re looking for here. Tell us what stock you use, why you use it, what you like about it, what you don’t like about it, what else you used on your quest to find the perfect stock, etc. Tell us what kind of shooting you do, how the stock you chose works with the kind of shooting you do, what other items you attach to the stock (slings, monopods, etc.) and how the stock you chose works with that setup, etc.

ETA:
Where possible, please try to insert links to the items in question to help new users track what you’re referring to.

For me it’s the LMT SOPMOD. I had one on a AR before I got my SR15, and was more than pleased that the SR15 came with one. I just like the cheek weld I get on it. I use a ACOG TA31H for my optic and it all feels like it all comes together with sight picture and cheek weld I get. As most of you know you need to get right in behind the TA31. I feel like the SOPMOD helps me with that. I plan on using this set up for a few classes this year, and eventually as a patrol rifle in the future. I’m using a Vickers 2 point padded sling with the QD mounts. I have the rear mount attached to the QD mount on the SOPMOD. That’s my story and I’m sticking to it!

I have tried
[ul]
[li]Vltor original (no longer in production)[/li][li]Vltor Emod[/li][li]Magpul M96 (no longer in production)[/li][li]Magpul UBR[/li][li]Magpul CTR[/li][li]Magpul MOE[/li][li]A2[/li][li]M4[/li][li]“Fiberite”[/li][li]LMT SOPMOD[/li][/ul]

I currently use the MOE more than any other. I actually find the stock to be one of the least critical items to change and so default to the M4 stock quite often, but the MOE is inexpensive enough with a slight advantage that I find beneficial (the rubber buttpad) that I will use it on a scratch-built gun over the M4 but won’t change it on a gun that comes with the M4. I also don’t think the CTR adds any benefit over the MOE for my purposes.

I like the UBR’s weight and general heft for benchrest accuracy type shooting, but dislike the added weight for moving-around guns.

I am interested in trying the new Vltor Imod because I think it combines the features I like in the original stock (shorter OAL) with the features I like in the Emod (attached buttpad).

I only use the SOPMOD and MOE, but do like the CTR and IMOD.

The SOPMOD is just a classic stock that has a great cheek weld and no play.

The MOE is simple, clean and cheap.

These stocks are used in “mallninja” training classes and preparing for Zombie attacks.

C4

M4

I use it for plinking, target shooting, and classes.

I have tried the CTR, MOE, SOPMOD, and a Vltor. They just didn’t offer ME anything over the M4.

I find it works in any situation.

I used to use Magpul CTR and MOE stocks. I liked them for the light weight and simple design.

Recently I have switched to the new IMOD stocks. I find they are a bit more comfortable to use and add almost no weight. It is a bit easier to use lower 1/3 co-witnessed optics with these than it was with the CTR and MOE stocks. Could just be mental however.

My SPR uses an EMOD which is very comfortable but balances out this particular gun a bit better.

I have also tried the original M4 stock and the LMT SOPMOD.

Usage is Training and home defense.

Oh and backing up Grant when the Zombies attack.

My preferred stock for most cases is the Magpul ACS. I like its cheek weld and how it makes most carbines slightly butt-heavy. I came to like these after trying A1, A2, original-type CAR stocks, M4 stocks, MOE, CTR and UBRs. I do use still use some of these other stocks too, but ACS is my preference.

I find that it is a very good length for me when I mount one of their enhanced buttpads - I tend to crawl up the stock, and I never have to worry about having my tender little cheek run off the front of the stock body as happens with some other stocks.

I generally don’t use my stocks for slinging since I prefer two point with either an ASAP or a Noveske QD plate, but when I did try playing with the optional ACS QD socket on the offside of the stock I wasn’t particularly pleased with the range of rotation - it just seemed like it was restricted to the wrong position. Not a problem, I just never sling there.

Based on my experience with several ACSs I’d probably like an EMOD, too - they seem like they would be similar in taste and feel.

I run IMODs on everything. I’ve tried ACS, CTR, and MOE also (in addition to standard M4 and A2 stocks.) I loved the cheekweld of the ACS, but not the extra weight. The CTR and MOE give me the lightweight I’m looking for, but don’t feel as good. The IMOD is the perfect balance of light weight and good cheekweld I was looking for, and I like that I can toss a couple spare batteries in there. On my training rifle I was looking to keep weight to a minimum without sacrificing utility, and I found that a IMOD with one battery tube taken off (in my case the right one since I shoot right handed) weighs the same as a MOE. On my competition gun I run the IMOD with both battery tubes since weight isn’t so much of a concern. I find that shooting weak-side without the battery tube isn’t a problem at all, it just feels like a normal M4/CTR/MOE stock.

My go to stock is the CTR. If the MOE had QD cups it would be my preferred stock as I don’t care about the lock. The CTR for me, is the best balance between weight, bulk, price, and cheek weld. I like the Vltor original and have a couple on carbines that have magnified optics due to the imporoved cheek weld. If price were not an option I would probably just use SOPMOD’s for everything. I do not prefer the ACS or EMOD. I’ve played with a UBR and like the feel but not the weight.

I have tried:

Standard M4
EMOD
MOE
CTR
ACS
Modstock
IMOD

I am a fan of the IMOD and dont see myself changing it. It balances great on my rifle: 14.5 govt. - larue 12". Weight is my primary concern, and the IMOD is lighter than the EMOD and ACS; and only about 1 oz more than the MOE. I like the cheek weld I get on stocks with storage compartments, so I prefer it over the MOE / CTR overall. It has a swivel sling attachment point, which is the mount I use, so it trumps the SOPMOD (plus the price on the SOPMOD is silly). The buttpad is very comfortable, and it locks up tight. Not that I need to be ninja silent, but the MOE rips my beard out when I have one. I am a weekly shooter and focus my shooting on timed drills / drills you experienced guys post. Very little bench shooting with my AR; so primarily standing, low ready. How I arrived at this stock? Im an accessory whore. I was sold on the MOE, but I prefer the length / width, cheek weld of the IMOD. It shoulders very nice for me.

I currently run ACS on duty rifle, it feels a little tighter with less play than my IMOD. And with the extra space to carry batteries and the ability to carry a spring repair kit in the stock. I don’t have to worry about remembering the extra parts or where I placed them on my gear.

Interesting thread, as usual Rob.

Most of my formative years with the weapon system were at a time when full A1 and (somewhat later) A2 buttstocks were the norm. I purchased a Colt Sporter II carbine for my own use in the mid-80s, and in this capacity, I grew accustomed to what we later saw in service trim as the USGI M4 stock. In those days, aftermarket stocks pretty much were limited to variants of the USGI carbine stock (i.e aluminum versus composite), or whatever companies like Choate or Quality Parts Company (later BFI) were trying to peddle.

I stuck with the original Colt stock.

Since I was overseas when the AR aftermarket really took off, I came late to the VLTOR, LMT and Magpul party, and spent no little time experimenting with various designs to determine which met my definition of “best.” The ones that I still have around in some capacity are:

UBR
ACS
SOPMOD
EMOD
MOE
USGI M4

Of these, I admire the UBR for the sheer brilliance of its design, the quality of its construction and the way it balances out an SPR or bench gun. As stated, this isn’t the stock for a carbine that you’re going to be running and gunning with in an all-day class, but I very much like it for more static environments.

I’ve no special attachment to the ACS, though it strikes me as typical Magpul kit. Good design, decent construction. I haven’t yet figured out what it does better than a SOPMOD or VLTOR, but I’m glad Magpul went ahead with it.

The SOPMOD inspires loyalty, pure and simple. While somewhat expensive, it does pretty much everything well, and leaves nothing lacking. Good lockup, no play, great cheekweld. Whether we’re talking about an SBR or a lightweight 16" rifle, the SOPMOD is hard to best.

The EMOD is a more recent acquisition, and one that I’m finding a good substitute for the SOPMOD. I’m not (yet) using the A5 buffer arrangement, but have reason to believe that the EMOD would shine even more with it. Like the UBR, the EMOD is a bit on the long side, but not objectionably so. A keeper with real potential for a 16" gun.

MOE/CTR stocks are already benchmarks, so I don’t need to say much about them. If you’re building an SBR, and not planning to use a SOPMOD stock, this is your solution. I’m not as crazy about them on 16" guns, but that’s largely just because I dislike muzzle-heavy configurations.

The standard M4 stock needs no introduction, though I find it amusing how urgently we feel the need to discard them for just about anything else. You can get a better cheekweld from a SOPMOD or VLTOR, but the factory stock works well, is lightweight, cost-effective, and – lest we forget – has by far the most “go to war” time of any of these contenders. I keep one LE6920 in full OEM trim, and see no need to change it.

AC

I use a Magpul UBR on my 16" middy with a Troy/Vtac extreme rail. Since the rifle is light to begin with, the extra weight of the UBR gives it a butt heavy balance which I happen to like. My other rifle has a Magpul 93B in combination with a LMT 16" upper with a Troy DI rail. If I were to get another AR I’d like to try the Vltor Emod.

I ran Gen 3/Gen 4, MOE, and SOPMOD on my issue rifle and my preference is in that order. Gen 3 stocks were too little for my sasquatch frame in body armor, Gen 4 were much better but would still slip off my shoulder when wearing kit. The MOE solved that, gripping well on my shoulder while in full rattle, but then I picked up someone’s SOPMOD and it was love at first sight. Excellent cheek wield, rock solid, slightly sticky rubber buttpad that never slips off, ability to stash batteries, durable, and they’re dead sexy.
What’s not to love? Oh yeah… that’d be their sticker price…

My first AR was a LMT SOPMOD in 556—thus the name chosen for this site—and I fell in love with it instantly. I built a lower during the “scare” post election and also added a SOPMOD to it because it resides on my 6.5 Grendel with a 4-16x50 mildot scope and for varying magnifications I prefer the adjustability of the SOPMOD. The training aspect is for CQB HD and for game with the 20" Grenny. I did recently get a wild idea and put an adjustable stock on my CX4 which gave it additonal USA compliance parts. The stock on that is the Vltor Modstock on a milspec tube from Palmetto. It was 1/4 the price of the SOPMOD, new, and a little modification of the Beretta buttpad gave it a little more comfort. That gun is a seconday HD gun as it is in 9mm but also very lightweight.

I’ve used the following:

[ul]
[li]A2
[/li][li]A1 (part of a Cav Arms MKII lower)
[/li][li]M4
[/li][li]Magpul MOE
[/li][li]VLTOR original modstock, clubfoot version
[/li][li]Ergo F93 (licensed clone of Magpul 93)
[/li][li]ACE ARFX (the longer one)
[/li][li]Magpul UBR
[/li][/ul]

I would be happy with a fixed stock in just the right length. The A1 and ACE are a little too long and the Sully looks like it’s a bit too short.

I’m fairly impressed with the light weight, feel, and tight lockup of the VLTOR. The only thing I don’t like is the butterfly latch on the clubfoot, but it’s functional enough. One of my favorites.

The Ergo F93 is a great shape and lighter than the UBR that replaced its design. It locks up absolutely solid and has about 3/8" adjustments to any length you would want. But I don’t have enough confidence in its construction or materials to recommend it on a serious gun. I suspect its buffer tube is 6061, and because of the simplified design it could be vulnerable to damage at the receiver/tube junction.

The ARFX is a very nice stock if you want a fixed stock in that length. The one thing I would change would be to ditch the foam overtube and replace it with a molded plastic overtube, to be less vulnerable to wear and damage. You could also do this yourself with tape, or maybe even plastidip, if you were so inclined.

The UBR is great, apart from the weight. The adjustment is simple, lockup is solid, I like the multiple sling mounts and I have more confidence in its construction/materials than I do in the Ergo F93.

If I were starting from scratch with my current knowledge, I’d be focusing on the VLTOR stocks.

EDIT to answer the various questions Rob asked:

My shooting is a mix of 2-gun competition, practice for 2-gun competition, and otherwise casual range shooting. I practice four standard positions (standing, kneeling, sitting, prone; excluding urban prone).

Generally I’m attaching a 2-pt sling to the stock, either with the standard loop or a QD socket. Most of the time it’s attached near the butt, not at the stock/receiver junction. I don’t attach anything else to the stock. I’m not currently using the storage on the stocks so equipped.

I find that any of the adjustable stocks work well for my shooting. I’m usually setting them to an LOP in the 11-12" range. The ARFX also works pretty well but is a bit too long to be ideal. The A2 does not work well for me when squared to the target and wearing any amount of outdoor clothing, because it’s too long. The Ergo F93 (aka Falcon) works especially well because of the small adjustments and wide cheekrest that slopes less than any of the others, but again, I have questions about its durability in hard use.

I have tried the Moe, Ctr, Vltor modstock and my go to is the CTR with enhanced butt pad. It is a great versatile stock and locks up tight.

I like Magpul stocks cuz they come in different colors!

Just kiddn’ Rob!

Actually, like you, I found the stock to be a not too critical piece as I progressed in technique.

When I first started shooting I tended to have the stock very high on my shoulder and out of pocket. This made the standard old 2-position type carbine stock with their small foot print uncomfortable and so I upgraded to the M4 type stock.

As the gun now sits lower into the pocket of my shoulder I don’t mind using pretty much any stock in a pinch, but they do contribute to comfort and balance so I still like to look at the different designs in the market.

My current default is the Magpul MOE. I don’t miss the friction lock as I don’t feel it in shooting, and the QD sockets are a non-issue as I prefer a different area to mount my sling. The rubber pad adds a bit of comfort also. Cons are I don’t have battery storage as I would prefer to have one set of batteries for my light and one for my RDS and since sights before lights for me, my grips usually have AA cells for my EoTech. (Not an issue with Aimpoint batteries)

On a 14.5" and up carbine with a long rail, vfg and light it gets noticeable that things get front heavy so I am looking at a heavier stock to balance things out. The IMod looks to be the front runner for me in this class. It has the heft to balance out front heavy guns, has the plus of a great cheek weld and lots of storage, modularity in configuration is a plus though I doubt honestly I would use it, and it has a rubber pad that the MOE spoiled me on.

Am also looking to experiment with the effect of fine-tuning stock LOP so am also looking at stocks with more positions and finer pre-sets but are light also which rules out the UBR. Maybe the Falcon M93 clone?

I like the Emod, it gives a nice cheekweld. I don’t use the storage tubes but appreciate the storage box as I keep spare batters and hex keys that fits my Eotech and Vltor light mount in there and the weight helps balance a 16" rifle with rail/light/VFG.

It’s also a bit longer stock so I can run it completely collapsed and avoid the “hair pinch” that many people accuse it of but which I actually think is the hair getting between the stock and the RE.

I have two and on one I’m going to try the A5 RE/buffer/spring system when they can be gotten as components to replace an A2 stock I have on a scoped 16". if this works out, due to it’s weight, I would trade the other one for an Imod.

I prefer the CTR to the MOE simply for the QD and I run one on another carbine with the enhanced buttpad for the extra length so I can run it collapsed down another notch. I prefer having as much of the RE covered so my cheek doesn’t overlap the joint.

I don’t find the M4 stock at all objectionable and have one on a light weight plinker using the SLAP plate for a single point sling.

I haven’t tried the ACS as the end caps on the tubes seem like something that I would lose. I also haven’t yet decided that the SOPMOD is worth the money they ask for it but would love one if I could find one cheap enough.

so now Rob, when is the definitive GRIP thread coming out??? :slight_smile:

MOE = Looks good works and CHEAP.

I would prefer an ACS because it looks cooler but is more expensive.