This is my Coal Creek Armory Invictus 1911 – Serial #3 of 25 built. These were hand built, one-at-a-time set-spec custom 1911s. Built from oversize slide and frames, every part fitted. This is not a worked over production gun, but rather, a full-on custom build by a qualified gunsmith (in this case, Bob Delmore). The specifications for this pistol were no compromise, a blend of the best looks of a classic 1911, while maintaining in it the best advances in parts and materials. During my tenure at CCA as VP, I set the specs for these pistols, as well as selecting the name long before it also referred to a Surefire flashlight, so I’m still very familiar with what went into these. So far, 25 have been made, #3, my personal 1911, is the lowest serial number on the market now - #1 & 2 are locked up at CCA.

Specs are as follows:
-
Oversize slide & frame by Caspian, frame manufacturer for Nighthawk among others. Slide and frame are hand lapped and fully fitted for 100& contact. Slide has proprietary oversize ball end-mill cut, a unique look. Frame and mainspring housing are Treebark patterned for grip without painful sharp checkering.

-
Cylinder & Slide Tactical II Lockwork, EDM Wire Cut, factory Rockwell hardness tested tool steel, for a perfect 4# trigger pull, and no worry of breakage or wear. The steel used, and the low stress machining process combine to make these the best fire control parts you can buy. The trigger pull is crisp, clean, no takeup or overtravel, and edge hardness is unmatched. Hammer, disconnector, sear spring & hammer spring.
-
Melonite (Tennifer) finish on all steel parts, If you’re not familiar with the Melonite treatment, it hardens(58-68 Rockwell surface hardness), slicks and rustproofs steel, Glocks, SIGs and Springfield Armory XD pistols all use it. You cannot rust a Melonite part, making it ideal for carry. The Melonite treatment is finished with Black Oxide(bluing) the color of which can wear under friction, but cannot rust.
-
Larry Davidson G-10 Grips – tougher than steel, light, and a very grippy but not uncomfortable aggressive checkering. The pair shown are a prototype set of double-diamonds, not released by Davidson on the market.
-
10-8 Performance Flat trigger – standard length of pull, but with no curve in the trigger face to “roll” the tip of the finger high or low. Pull is straight-back, no matter where you put your finger on the trigger. The best feel available in a 1911 trigger – I use them in 3 other pistols. The trigger was IONBond Diamond Black finished, a tungsten Diamond-Like Coating that prevents scratching, and keeps the trigger matte black after hundreds and hundreds of rounds.
-
ED Brown magazine release – not huge and oversize, just long enough to hit with ease, cheackered face.
-
EGW Heavy Duty Slide Stop – Machined from bar stock, machined and heat-treated, round pin, serrated pad.
-
Ed Brown full pin set –all pins in the pistol are heat-treated steel.
Heine “Straight Eight” Tritium sights. Dot-over-dot sighting. 2008 manufacture, bright Trijicon tubes, fits in the Novak cuts.
-
ISMI standard weight (16#) recoil spring.
-
Ed Brown barstock plunger tube.
-
Ed Brown GI Guide rod.
-
EGW Thick bushing & cap, radiused to match barrel. Snug accurate fit, but still hand-removable.
-
Kart NM Oversize barrel, fitted to slide and radiused at an angle to the barrel bushing. Locks up like a bank vault, with an audible click.
-
Ed Brown Tactical safety, single side.
-
Ed Brown Flat blank Mainspring housing - Treebark stippling treatment, keeps it grippy. Butt edge is radiused for comfort and to prevent garment wear.

-
Ed Brown Hardcore firing pin
-
EGW Oversize firing pin stop
-
STI Competition fitted grip safety – blends perfectly into the slide, very high-rise & comfortable, memory bump
-
Ed Brown Hardcore Extractor, 4340 Tool steel, like all the Ed Brown Hardcore parts, has a lifetime guarantee.
I put less than 500 rounds through this 1911, and carried only a few weeks total. It shoots extremely well, handheld from a bench, it will shoot a 1-inch group at 25 yards with Remington UMC junk off the shelf. This is more proof that Bob Delmore can fit a Kart 1911 barrel perfectly, than any demonstration of my shooting prowess. Every action on this pistol feels glassy smooth, slide, safety, and the trigger is perfect. I tried to keep this one as nice as I could, knowing it was bound to be a collectible item in addition to being a truly high-class, full-custom 1911 build. It has a pinpoint spot of wear on the triggerguard, some light wear on the rear sight, and the barrel hood is a half shade lighter than the rest of the coal-black Melonite. Other than that, it is impeccable. Any chance in blackness in these pictures is oil, I wiped it down before photographing, and should have used a fully dry cloth.




This custom 1911 also comes with:
-
3 Chip McCormick Power Magazines, with Tripp Research Super 7 spring & follower upgrade kits. These are the best and most reliable combination of mag body and internals available, treated with the Same IONBond Tungsten DLC, making the mags black, supremely slick, rustproof and scratchproof. These mags cost over $50 each between component parts and IONBonding.
-
MTM hard case, as delivered from the shop. There were supposed to CCA logo stickers for the cases, but just like the manuals, never got finished before the pistols came into fruition. In the end, all pistols were delivered to customers in blank cases.
-
Brommeland Max-Con V holster, in excellent shape for IWB carry – these holsters go for $169 separately, slim, comfortable and very concealable.
I took very good care of this pistol, and don’t wish to part with it, but like my Springfield before it, needs to be turned into home repairs. This pistol cost me just over $2k new as a preorder, and they rose in price before the project wound down. In terms of parts quality, they are unparalleled, as you can see from the listing – the parts alone total over $1200 of the price of the 1911, before 40 hours of labor per gun, and rustproofing Melonite treatment. In terms of build quality, Bob Delmore did an impeccable job with this pistol, and it will shoot with a Les Baer, without being too tight to rack. 1 inch at 25yards is tested and repeatable, and accurate as it is, it is not so tight as to be unreliable – 100% function over 500 rounds. With the mags, holster, an unmatchable low serial #, and a well-kept condition, $1649 shipped to your FFL is a steal. Email Kingsiderook@gmail.com with any questions, I will accept Money Order, Certified Check, or Paypal +3.7%.