? about my BCM Middy

I have less than 100 rounds through it , I’m using a regular charging handle and a LMT F/A BCG and H buffer. Should I have this much wear already with such a low round count?Thanks guys for your replies.



Do you have a Macro Setting?

No sir I don’t

I doubt anybody will be able to gauge anything from those pictures.

With that said, is this your first AR? I vividly remember a couple of years back when I got my first one, I was pretty freaked out about the wear. In fact I was convinced that the charging handle channel was out of spec(as I’d seen wear on two charging handles.) I also thought the cam pin was going to chew right though the receiver. Neither was a problem, I was simply paranoid about my investment.

Chances are high(especially with that setup) that what you are worried about is entirely normal.

ack… those pictures suck balls, dude. :slight_smile:

all i can make out is the streak in the CH channel. that’s really common, dont sweat it. ive had receivers that dont wear at all up there, and ive had receivers that completely strip off all the park along that path after less than 100 rounds. once the parts mate up the wear stops. just squirt extra lube up there

+1 agree

If your CH is out of spec you’d know right away, trust me. I experienced this when building up my BCM mid-length, my factory Stag CH was 10mm too wide, and was nearly impossible to cycle by hand.

Personally I wouldn’t be overly concerned. Be sure to oil and you should be RTG.

:smiley: Yea I know, the pics do suck,but yes I was talking about the wear with the ch handle and the cam pin wear.
No sir it isn’t my first AR,I just haven’t experienced wear that prematurely in any AR that I have owned or seen in any of my friends rifles. I wasn’t sweating it , just asking for info from those of you who might have had a similar situation.Thanks all.

Put a thin coat of grease on your carrier rails where you see the bearing marks on your upper. It stays put much better than soaking the whole carrier in lube.

Are you sure you don’t? Most all digital cameras has something that looks like a “Flower” on them. That is your macro setting.

C4

As far as I can tell, that really isn’t wear, but the dry film lube inside the receiver wearing. This is 100% normal (generally speaking).

If you can get someone to help you with the pics, we would have a better idea of what we are looking at.

C4

That’s about the best I can do picture wise.Well C4Grant, since I got the upper from you I’ll take your word as gospel on this one. Like I said I just never seen wear like this with less than 100 rds. And I run my AR’s real wet when shooting. Thanks all again.Oh and BTW this is how she shot first time out. Check out the MK262 groups. :cool:The AE black box and PRVI was at 100yds

looks like the dry lube to me too ,clean it and look again ,I always run mine wet with a good lube (Mobil 1) and I have 3 BCM uppers and have never noticed that white flakey stuff on mine. did you oil it B4 shooting ?:confused:

Gonif , Not the white flaky stuff, but if you look right above the forward assist you will see bare metal. I run mine real wet, BCG and all . I use Slip 2000/EWL and CLP exclusively.

My BCM has similar wear in the same location on both sides. 600+ rd.

are there any burs on your BCG that may be causeing it ?

I have about 320rds through my BCM midlength upper. I don’t have any wear like your photos are showing - certainly no bare metal exposed. I do have the (what I assumed was) mottled/blotchy sort of looking anodizing inside though (never bothered me, so it’s no big deal). It shoots real well, which is all I’m concerned about. :slight_smile:

Real big pics:

(even though that spot looks shiny, there’s no bare metal there - just wet with Slip2000)

Geez, I never would’ve thought a little piece of lint would look so darn big.

To Gonif, Buckeye, C4Grant and all others thanks again for the replies to my post.Gonif I don’t have any burrs on my carrier, I personally just haven’t been,well let’s say bowing down to this particular upper because it’s sloppy loose on 2 lowers I have tried and ok on 1, and then this wear shows up.But I’ll say it before others say it. JUST SHOOT IT.:smiley:

if you’re not happy with it i’d be happy to buy it off you, bro

maybe you should send it back to BCM and let them look at it .:wink: they buy the upper receiver from the same sorce as LMT,Colt and others and you hardly ever see upper receivers that are a problem . if it is gouged like you say I would take a long hard look at the BCG.:confused: