Vltor A5 Setup for Multiple Uppers

Hi all,

Hoping you can guide me in the right direction. I currently have a franken AR15 and have an SAS M47 in jail. This upper as well as the second one (see below) will be running suppressed 100% of the time. I’d like to replace the Magpul PRS with a Vltor A5 system since I will be running two uppers and have a few questions hoping you could all answer.

[ul]
[li]20" Bartlein barrel with rifle length gas system
[/li][li]SLR Sentry AGB
[/li][li]Magpul PRS stock
[/li][li]Seekins Upper and Lower
[/li][li]FailZero M16 BCG
[/li][/ul]

  1. Do I need any additional buffers or is the H2 fine for the rifle length setup?
  2. Should I get the green Sprinco spring?

I plan to form 1 the lower and swap out the 20" upper with a 11.5" BCM or MicroMoa upper.

  1. Should I use an H3 or H4 buffer for an SBR setup?

If I get the BCM upper, I’d also purchase a Gemtech SBC or LMT enhanced carrier. I’ve read the other threads and sounds like either will do a great job with gas blowback and partners well with the A5 and green Sprinco spring.

If I run the MicroMoa upper, I will use the FailZero BCG (or purchase a second BCG) and the green Sprinco spring.

Is there anything else I need to consider or purchase?

Thank you!

If an upper won’t run right on an A5 with the standard buffer, it need fixing.

Mark is correct. However, I tend to prefer the smooth feel and overall reduced gun movement of the A5H4.

Depending on the combo, an A5H4 may be too much mass for some, for others it could be a choice. Same with the A5H2, just depends on the combination.

I whored my lower around the range the other day. It is a vltor a5, green spring, and a5h4 buffer. Ran fine with a colt 6920 and brass case, and ran fine in a new 16.1 ddm4 middy using steel case monarch (academy brand brown bear I think).

I tried an A5 with supplied buffer on a 10.3" suppressed full auto Colt, 14.5" Colt carbine, 14.5" BCM mid, 20" BCM rifle with no issues at all.

I run my A5H4 on my Sionics reduced gas port, suppressed 11.5" (and unsuppressed). Same lower, also on my suppressed and unsuppressed Faxon 18" barrel with rifle gas.

Adjustable gas blocks both.

Thanks, everyone! Extremely helpful. I will start out with the A5H2 and pick up and A5H4 to test as well.

@BufordTJustice. Great note on the AGB shutting off for both uppers. I will try that as well. I will add Sionics to the list of uppers.

Please explain, I thought heavier buffer was to address the larger than ideal gas port. And if you were building a ground up custom gun you would use a smaller port and something like an A5H1

According to Vltor the A5-3, and A5-4 buffers were created with suppressed and piston driven guns in mind. That having been said, there is no reason why they could not be used on a overgassed upper to help slow it down. That would be a band-aide use for the buffer however. When dealing with a suppressed gun, the -4 buffer is not over-buffering the gun.

The -4 works in everything I’ve tried it with, so far. Including my 16.1" middy, and another new DDM4 16.1" middy. DD uses a 0.073" gas port on those guns.

This has been my experience as well, from SR-15s to 6920s to factory and homemade SBRs, suppressed and unsuppressed, the A5H4 has never let me down.

Yup, wouldn’t disagree with that either. The -3, and -4 aren’t over-buffered for most non-suppressed guns either, as the experiences posted in this thread convey. I’ve tried the -3, but not the -4.

My A5 buffer says “VLTOR A5 PAT PEND”

I bought it like 6 years ago. Anyone have any guesses what it might be? A5H2?

That is an A5H2.

Yup. They are still labeled this way, more or less. The buffer/spring kit that I just bought is labeled “A5, Vltor, PAT #__________, OTHER PAT PENDING”

I have more than a few A5 combos that won’t support an A5H2 without a can. I have more than that that won’t support the A5H4 without a can. The exceptions are not unicorns. There’s plenty of stuff out there gassed pretty hard, some not so much. For myself, I tend to like the lighter ported options over the harder gassed ones.

That gets to my question. Is there a benefit to setting an adj gb to the 4 vs 2 buffer?

For a matter of convenience, the A5H4 setting is probably better than what they may have used before. That does not mean the A5H4 porting is really best, just better for some from their own perspective on prior combinations. That is not a negative in intent, it can be truly better than what they had before. There’s many combo’s out there.
For most, you really do not need more than an A5H2 for function. The A5H4 can mask by overlap in function for many combinations. That does not mean that the A5H4 is better over other possibilities. You can further widen the span of function using a dedicated mass to that need for that porting. If you make a base on the highest mass of function, you lose options that would drive the system higher into issues with options, like a possible can and/or ammo.
If variables like a possible can addition and or different port pressure ammunition may happen, you can tailor the reciprocating mass for that or those options if you are not at the normal limit of mass in either direction. You achieve a wider span of operation for those circumstances. Sure an A5H4 based combo may work better than an A5H0 for a wide variable, it does in this system. That fixed mass system is still inferior to a more tailored system by a margin.
Oversized gas ports restricted by possible adjustable gas blocks aren’t preferred for long term use. Oversized ports erode the barrel at the port no matter what the further down restriction in flow may be. Wire drawing by high pressure gasses for erosion depends on the gas cutting from escaping gasses at the base of the bullet. The action in drive may be restricted by the additive function of that gas reduction, the port erosion is related to the base port in the barrel in general.
I prefer specific porting with mass options available over the adjustable gas block and those fixed masses for many reasons beyond these cited examples.