TR24G moa and hold over info request?

I am looking at purchasing one of these within a day or two and was wondering what the actual moa of the triangle was top point to bottom? Obviously it does not matter at the top point if you are using that as your aiming point but I was wondering is there a way to range your targets with this recticle or is there a hold over for say 200, 300 yards for this recticle? Thanks E1…:confused:

The Triangle is 12 moa I believe. When I had one I sighted the tip in at 200 yards and found that the bottom of the triangle worked for 300 yards. Past that you need to dial in your elevation with the turrets.
Pat

I think 0-300yards is where the TR24G really works well on a 5.56 carbine. I dont like to rely on the bottom of the triangle to range as the triangle covers up too much out past 200yds. I just work off of the tip of the triangle.

I would really like to see a green chevron with some ranging lines out to about 400yds on this scope. I still love it as-is though.

I run a 100yd zero, and at 200yds my hold-over is approximately *2.75"

At 300yds my hold-over is approximately *13"

*This is all dependent on your barrel length, twist, ammo choice, etc.

I agree with Nick it is a great scope for 0-300. I have the 24R and I have been extremely impressed with it. I however use a 50 yard zero. With a 50 you are never more the 1.5 inches high ( at about 140 yards) and don’t need to hold over until about 225 yards. At 300 you have 5 to 8 inches of drop depending on bullet velocity. It gets a little fuzzy after 300 due to the type of reticle.

Matt

Thanks for the replies guys, I just ordered one yesterday and am anxiously awaiting it to arrive.

What would be a good mount for this scope? I was thinking Larue, but am open to others. I am wondering if I need an extended eye relief scope for my flat top AR15?:confused:

You will love your Trijicon TR24. I kick myself everyday for selling mine. After seeing what’s new at Shot 2011, I may buy another Trijicon, a TR24R.

I had both an American Defense Recon-X and Larue Tactical SPR 1.93.

Both are very high quality. My issue with the ADM was that the adjusters only had six lugs, one posistion was too tight, the next too loose. They now ship with eight lugs. To make sure you got one of those, I would order from ADM direct or call and speak with someone to make sure you know what you’re getting.

That being said, I liked the Larue a little better. I prefer Larue’s rings. There are less screws and I also like the way they enter from alternating sides of the mount. The Larue also felt a little lighter in my hand, but it wasn’t a huge amount. It could have very well been the difference in numbers of screws. I also like the tension adjustment of the Larue mounts, and the levers seem easier to move, regardless of tension.

Bobro is another option, and they are neat in the fact that they auto adjust. The mount Trijicon lists on their site is a Trijicon branded Bobro mount, if that tells you anything. They are expensive, more so than the other two options i’ve listed. I have no first hand with the Bobro, but user reviews i’ve read have been strong.

I like the higher mounts for the TR24 type of scopse, if you plan on using it a lot at 1x. I like the releif cuts in the side of the higher ADM mount, looks good.

If you plan to mostly live at longer ranges, I would get the lower mount.

If the extra-extended mounts aren’t avaible, you can always mount the scope so the turrents are forward toward the front ring. Its almost an asthetic thing, i’ve owned both, and both have worked well.

The TR21 had a longer eye releif than the TR24, so with that scope I would recommend getting the extra-extended mount to push it further out over the delta ring. With the TR24, it isn’t a huge deal.

What upper are you going to mount it on? If you have a continuous top rail you wont need to get the extended eye-relief mount.

I initially ran the higher 1.93" height LaRue LT-135 mount and really liked it. Especially for CQB work. But I found that it would not clear part of my rifle rack at work, so I switched to the lower LaRue SPR-E (Extended Eye Relief) mount. It took a bit of getting used to, but after a few trips to the range running some drills I think there is very little difference in speed running CQB drills than the 1.93" mount for me.

Personally I would stick with the LaRue SPR-E (LT-139) mount for the TR24G. If you don’t like the mount, Im sure Mark LaRue will swap it out for something that works for you if you call and speak with someone directly at LaRue Tactical. Great mounts backed-up by the greatest customer service in the industry.

nickdrak,

here is what I have to put it on!

http://noveskerifleworks.com/cgi-bin/imcart/display.cgi?item_id=lr-vtac&cat=154&page=1&search=&since=&status=

I am thinking the Larue mount will be the way to go. I am just worried about the eye relief since I do not have the scope yet. Should be here on Friday so I need to order a mount soon.:confused:

You guys could post some pics of your rifles with your TR24’s attached and that may help me out!!

I’ll post a pic with the TR24 and the ADM mount I had it in.

You wont have a problem with the Larue and the TR24.

Here is my BLT. This is the 1.93 LaRue. Id like the shorter mount.

Here ya go:

Your Noveske/VTAC is very similar in concept to my home built 16" Middy pictured above. Very cool! I got a feeling that thing is gonna be a shooter;)

so nickdrak, what is the model # of your Larue mount? I was thinking the lt-104 for me but it appears that you have the extended mount? Looks good btw too!

Correct, I am running the Extended Eye Relief LT-139. As you can see from the pics I run my stock one click out from fully collapsed. If you run your stock further out you should be able to get away with running the standard LT-104 and still keep it mounted on the receiver and off of the handguard. I ran my 1.93" height LT-135 partially on the handguard by bridging the receiver rail and the VTAC handguard rail without issue, but some dont like to run it that way.

Mount looks really high, how is the cheek weld with the SOPMOD?

did you forget to post the pic???

The mount is pretty high. LaRue suggests the 1.43 unless you need the 1.93 because of a laser/ir. Some folks like the 1.93 because it makes you keep your head up.

I traded an H1 mounted in a LaRue mount along with a new LMT BCG and a spare SOPMOD for the scope. The SOPMOD helped balance out the gun for me. I liked the cheekweld. I’ve gone back to a CTR on this gun to match my other guns. I like running my 2 point sling through the end of my CTR. I don’t care for the QD at the end of the CTR or SOPMOD if it had a rotaion limiter it might work better for me. I think I will save some money and buy a MOE with my next gun.:smiley:

I have 4 of the Tr24 triangles, all are mounted in the Larue 1.93.

I went for the higher mount for more of a heads up style. I use these on duty/SWAT.

On a AR with an F marked FSB, will the LT-104 give me a lower 1/3 co-witness or an absolute co-witness?

You cna’t really co-witness through a magnified optic even at 1X.

With the mount I have it is not even an option. The scope is too high. I tried with my initial install to mount the scope forward enough so I could flip up my Troy rear sight. It worked but the scope was too high to co witness at all.

Eagle not sure what you meant about the photo. I only have that one. I could snap a photo of the gun now. With the CTR if you want. I also swapped the 11" tube for a 13" tube and the bolt hold open unit is gone. I need another BAD lever and I am done.:smiley: