I have been looking for a replacement barrel, preferably a complete barrel assembly, for a Colt 6721.
I noticed several barrels listed on Gun Broker with descriptions such as:
“This Colt Barrel Assembly is a new take off from a Colt AR6721”… “This assembly was test fired at the Colt factory. It has been removed from a complete M4 rifle assembly and is presented as shown. The born on date is 10/16”.
I sent an email asking the seller how they came by the barrel but being the weekend, I haven’t heard back from them yet.
My question is why would someone disassemble a new rifle and part it out? Is there any reason to be concerned the barrel is from a stolen gun? The seller had nearly 10,000 reviews with only a small number being unfavorable.
That’s interesting. Is it an M4 or M4A1 profile? If he’s that big of a seller, he must be dealing with liquidators or something. My guess, and this is just a guess mind you, is that the barrel failed one of the mil-spec inspections and was rejected. It may have been that a batch of M4s delivered by Colt didn’t meet the inspection requirements, so they took them off and replaced them, then liquidated the rejects as factory seconds. My guess would be that they failed the accuracy requirements, or that some of the chambers had burrs, or something like that.
In any case, I would be very curious to hear the seller’s story, so be sure to let us know how it ends.
ETA: For the record, though, I wouldn’t touch a 14.5’’ barrel with a ten foot poll. I’ve been down that road, and it’s a royal pain in the ass if you ever need to work on it or want to upgrade it. Saving that half inch of length just isn’t worth it.
I bought a complete Colt LPK (including FCG) for $100 off GB from a dealer in MD who was parting out 6920s, and then I went back later and got a complete 6920 lower from him. I would guess he may have been having trouble moving rifles after MD instituted their ban, but I’d also bet that he found that he could make a little more by parting out the rifles than by selling them complete. Colt parts aren’t that easy to get and are often expensive when you find them (e.g. SAW). In the case of your seller, he (or another customer) probably wants to put a mid-length or some other barrel of his preference on the 6721 and knows that he can recover some of his cost by selling a Colt barrel that isn’t readily available elsewhere. I see people do this pretty often with Colt parts, so I wouldn’t be too concerned about something fishy going on, as long as you can get photos to confirm is authenticity and condition.
Okay, 3ACR’s post made me go back read the op again. So is it an AR6721 barrel, or an M4 barrel?
“This Colt Barrel Assembly is a new take off from a Colt AR6721”… “This assembly was test fired at the Colt factory. It has been removed from a complete M4 rifle assembly and is presented as shown. The born on date is 10/16”.
Something’s fishy here. Perhaps he meant to say it’s a take off for a Colt AR6721? Either way, it doesn’t make much sense…
It would help if you could provide a link to the listing.
It’s an HBAR barrel. The add had pics and the markings appear to all be correct - C MP 1/9 Nato 5.56.
Does Colt release their “rejects” for resale? That seems like a poor business practice - people buy a “Colt” marked part, it doesn’t work and blame Colt. I would think they would destroy their failed parts in order to protect their reputation and avoid liability issues.
This Colt Barrel Assembly is a new take off from a Colt AR6721. This barrel is the Colt H-Bar, it is 16” long and includes the bird cage flash hider, “F” marked front sight with gas block, gas tube with pin, sling ring, bayonet lug, barrel-receiver delta ring, and Colt handguard. Please note this has the yellow inspection mark under front sight tower. The barrel is chrome lined, has the M4 feed ramps and 1/9” twist. This assembly was test fired at the Colt factory. It has been removed from a complete M4 rifle assembly and is presented as shown. The born on date is 10/16.
This is a genuine Colt Barrel assembly in new condition ready for that AR project you have in mind or stash this one for the future and burn up some ammo.
What if the barrel was removed as the person who bought the rifle had other plans and just wanted all the other Colt components?
Not too long ago, another gun forum member bought a BCM KMR upper and I replace the barrel with a Sionics reduced gas port size for him that he wanted. He specifically liked the BCM setup, but preferred the port sizing of the Sionics barrel as he was going to shoot it suppressed nearly the entire time, so he opted to just buy the complete upper, swap the barrel, and then sell the unfired out side of factory barrel, which he got good money for.
After selling the factory BCM barrel, it was about a wash to have the exact upper he wanted at a good price and saved him time on sourcing the parts individually due to stock availability at the time (build a few months before the election).
It’s an HBAR barrel. Says it is off a 6721. It has a 1/9 twist to which to the best of my knowledge is only available on a 6721. 6721’s do have an “M4” marked upper receiver. I cut and pasted their description in this thread.
Gotchya, it just threw me where he said it was from a “complete M4 rifle assembly.” All Colt uppers are marked M4, but M4 feed ramps does not a “complete M4 rifle” make. I don’t know if it was his intention, probably not, but the way he’s wording it leads one to believe the barrel came off an actual M4.
ETA: But it looks like a good barrel, so I would snatch it up if the price is right. If you’re okay with the weight of an HBAR and the carbine length gas system, that is. The 1:9 twist is a huge plus in my opinion. M855, and especially M197, are going to be substantially more accurate from a 1:9 than a 1:7.
This happens quite often and I wouldn’t worry about it whatsoever. Many people buy & part out factory Colts. They might be only after the lower or just want a different barrel than the factory one.
Just to add to my previous comments, I see nothing in the description to indicate that this came from Colt as a “take-off” barrel. I read his description to mean that he himself took it off a 6721 for whatever reason. The possibilities are endless. Just as another example, before Colt introduced their 6921CK, I was planning to buy a complete 6920 and a 14.5" M4-profile barrel, swap them out to build an M4gery (as people used to call them), and then sell the 16" barrel. With the release of the 6921CK, I instead found the complete 6920 lower that I mentioned previously and have now been procrastinating on buying the upper (which will get a pinned A2X).
Colt parts always seem to be in demand, or at least sellers think they are. I noticed that people are now listing Expanse lowers on GB for the same price that I paid for my 6920 lower a couple years ago.
Maybe he wanted a precision hard use gun? Getting a colt and throwing a match grade barrel and ff tube on it would be a good way to do that imo. Just a thought on why. The possibilities are endless.
Visit the Equipment Exchange. These barrels pop up there from time to time. I recently bought a Colt take off barrel from a forum member. Great barrel at a great price.
The last Army test I saw showed that 1:7 had a detrimental effect on accuracy. And we all know that 1:7 is excessive for a 62gr bullet, and way excessive for a 55gr one. Hell, it’s even excessive for an 80gr bullet. Something isn’t adding up here.
ETA: Here’s the first result that came up on Google. Apparently the twist rate issue is being carried over to the new M855A1 as well. 1:7 is just too tight for .223. A bullet long enough to favor that twist rate simply won’t fit in a .223 case and still load into a mag.
I don’t have much say in the matter. Only HBAR AR’s are legal to be sold in Maryland after October 2013.
If you owned one prior to that, you are grandfathered.
I purchased this Colt, which is a Wisconsin Police Department trade-in, a couple months ago. Since it was an HBAR, it was legal for me to buy as a Maryland resident. Now I want to re-barrel it. Since I purchased it after October 2013 I MUST put an HBAR barrel on it to remain within the law. In all reality, I could have probably just put a 6920 upper on it and went on my way and never had an issue, but by the letter of the law, that would be illegal.
Had I purchased this rifle BEFORE Maryland’s latest gun laws went into effect in Oct 2013, I would be free to put any barrel available on it.