SBR build: Which lower for life?

I’ve read pages of threads here and the SBR sticky. I’m a NC resident in a no-sign county and will be going the R&D trust route having read the arguments and NCGS 14-288.8 a few times. I plan on building a flattop 10.5" SBR AR, later adding a can to it with the next stamp. Right now, I’m looking at the Noveske 10.5’s with the switch block. This will be a range toy, and for the occasional 3Gun match fun match, and of course the testing basis of a piece of ballistic software to remain true to my 14-288.8 R&D. :cool: This SBR will probably also have a .22lr bolt in it 50% of the time or better as my local range is rimfire only. (hence the extra benefit of the switch block to close off the gas

Now it’s time to order the lower, make sure it’s in spec & everything per the sticky. Who to use?

I kind of like the billet lowers, all my rifles have forged ones now. I want a lower that’s well made, will engrave nicely, and would be supported down the road. Longevity is the biggest concern.

LaRue:
http://stores.homestead.com/Laruetactical/Detail.bok?no=248

Mega:
http://megamachineshop.com/armscatalog/006BILLETLOWER-GTR-3S/loader.html

Any suggestions on which lower to start with? Are there any manufacturers that can sell a lower engraved with my intended trust name up front?

Just pick what ever logo you like. I went with Noveske. I think my next will be the Spikes Bio Hazard lower. That is unless a certian suppressor Co. comes out with there own logoed lower at SHOT.

Jk

If you’re going with a Noveske SBR upper, you might want to check with them on doing a Noveske Form 4 lower rather than a Form 1 lower of another make. That way you don’t have to engrave it at all and if you ever do have to sell it, you can get full value for the lower.

Not something everyone will care about, but it’s worth throwing out there.

There is no reason not to do this. ToddK gave more details in another thread in this forum.

With regard to swapping uppers, is there any difference between a Form 1 and Form 4 registered SBR?

I was hoping to buy a second 10.5" upper at some point for the same SBR lower.

No difference and you can have as many SBR uppers for a registered lower as you want.

Skip the billet lowers.

As long as the lower is 7075 and anodized correctly and everything is in spec it will last a very long time.

Me personally I am going with either a Daniel Defense(if my dealer can get me a good price on it) or an Aero Precision for my SBR build. If I could get a Noveske for a good price I would probably go that way as well.

Anyone offer engraving at the time of order or are any engravers an FFL so that I can mail a lower to them & back directly?

I bought a Noveske matched upper/lower for my SBR, build, used a BCM BFH 11.5 inch barrel. Worked out great. Noveske and Rainier Arms usually sell those matched uppers/lowers for $250.

As to engraving, Ident Marking services in Texas and Orion Arms in Minnesota are both 07/02 FFL/MFGRs that can legally receive your receiver and ship it back to you. They both do a great job. I’ve used Ident because they were a little cheaper. I have the engraving done in a 1/16 inch font in the trigger well and it was some very nice work.

http://m4carbine.net/showthread.php?t=69631

Here is the link.

I recently got a Spikes billet lower that is a very nice piece, and it comes with an ambi bolt release.

I had my lower engraved at a local trophy shop. 10 min and $10.

Jk

As for the engraving, it has to be .003 deep or deeper and simply say:

Surname R&D Trust
Cary, NC

Where Surname R&D Trust is the name I intend to use on the Trust to register it?

In my discussion with David Goldman of guntrustlawyer.com, the lower needs to be engraved as the name of the trust appears on the Form 1.

ie
B HOGG TR
FAYETTEVILLE NC

My trust was created and notarized as B HOGG TR, not Boss Hogg Trust. “TR” is a legally accepted abbreviation for Trust just as “ST” is for Street.

If I ever go down the road into SBR land, I’ll be bringing a Knight’s Armament lower with me. I shoot lefty so having ambi controls is awesome. Plus, I like the “Stoner Rifle” roll mark.

Thanks all. I went with a POF 7075-T6 billet lower, gen I.

I found a local laser & mechanical engraving shop that I’m going to try once my Trust paperwork is setup & signed. I’ll probably have them engrave an older receiver first to make sure it comes out clean before having them do this one.