Odd bolt-over (?) malfunction

Without dragging the manufacturer through the mud, I’ve got an AR that has an extremely odd bolt-over problem. The bolt isn’t stripping rounds off the mag. Extraction/Ejection is normal. Even if I lock the bolt back, insert a fresh mag (downloaded) and let the bolt slam forward, it just rides right over the round it was supposed to strip and locks into battery. Bolt has normal range of motion, goes back far enough in the receiver.

Bolt looks normal too and there is no odd wear apparent inside the action. Tried multiple mags, same issues.

I’ve contact the manufacturer, but they’re most likely swamped.

Anyone ever had this problem?

ak,

What type of mags were they? Though you may not want to drag “their name” through the mud it often helps if we know who it is so we can narrow it down.

what’s the bottom of the bolt look like? pics?

if you’re taking pics too, can you snap one of a loaded mag inserted into the lower with the upper assembly taken off?

DPMS .308.

The mag, bolt, upper, and lower are all DPMS.

No abnormal wear noted on the bolt. The only things I’m thinking that could be out of whack are the bolt, upper, or lower. All 4 mags I tested are doing the same thing.

Just wanted to note that this isn’t a “they ain’t fixing it” type deal. Haven’t tried to contact them too hard yet.

Did the mags come with the rifle or were they purchased separate? Something tells me that the mag is not seating high enough to allow the rounds to be stripped. Or did I misunderstand what you were saying?

Yup, the rounds simply are not being stripped from the magazine. Just not sure if this is a mag issue, a receiver spec issue, or a bolt issue.

All the mags were purchased from a well known and respected dealer, they’re DPMS factory mags. 4 mags in a row would be kind of a record though.

Try a new Magpul .308 mag :wink:

You don’t say, but I assume that it is brand-new? Brand-new to you?

Take a peak at the mag release? Did you load the mag so that the bullets are on the left or right, does that make a difference? Bolt has all its lugs, right :wink: Be great if you could swap lowers with someone else.

Hard to believe it was test fired?

Don’t be shy about posting before calling the manufacturer. Nothing like thinking there is something wrong when there is a quick fix.

Brand new parts.

Posting rule #4 is why I was hesitant.

  1. Contact The Manufacturer or Dealer First – Internet forums have a large global audience and unsubstantiated or ill-informed comments will affect the livelihoods of a lot of hard working people in the industry. If you have an issue with a manufacturer or dealer that you would like to resolve, we ask that your first contact them to resolve it.

ak,

The difference is you were seeking advice/ info about an issue. You didn’t come here dragging them through the mud calling them crap. I am sure that the Mods will agree with that.

You need to isolate the problem. Other mags, upper, lower, etc… Or just try and contact them directly and tell them you want a speedy resolution and not dick with it. It all depends on your patience factor and if you need it now. I tend to have a low BS threshold when it comes to stuff like this and I would probably have returned it and bought something else. But, that’s just me.

sure seems like the mag/top round is not high enough. when you insert a loaded mag in the gun with the bolt forward, can you feel the stack being pushed down a bit?

what does the feeding motion look like when you SLOWLY try to chamber a round?

I think I isolated what was causing the bolt overs.

About half of the DPMS mags had deformed feed lips, didn’t notice it at first until I had a decent mag and a deformed mag side by side. I’d chalk it up to shipping, but when half the mags are all deformed on the right side… no comment. Careful application of a redneck leatherman (screwdriver) on the problem area cured the deformation issue.

I also tightened the mag catch to grip the mags a bit more snug.

Ran a snap caps through the mags many times over with no problems.

Hopefully the problem is solved and the rifle will prove to be a good shooter.

Armakraut,

Though you think and it may appear that you fixed the feed lip issue with those mags I wouldn’t use them for anything more than range practice. Hopefully your problem is cured and you can give us an update after you have put some rounds down range.

Looking forward to putting a couple hundred through her as soon as I can.

i want to know how you found a DPMS .308

were you on a waiting list or something?

i’d really like to have an AP4 someday.

R-Guns seems to be the best source for the DPMS .308 stuff. There might be a slight backlog, but they otherwise seem to get anything DPMS a lot quicker than anyone else. Mine had a chrome lined barrel custom installed, the rest is DPMS though. I purchased it one lego piece at a time.

One thing that might be of interest to you, CMMG is coming out with a lower that takes SR-25 mags, and Armalite uppers… and magpul is doing SR-25 compatible mags soon.

thanks much. sounds like a really nice battle rifle you have there.

i saw the big boy pmags too. they look cool. thanks for the heads up on rguns and cmmg. i’ll have to look into it.

i still have 5.56 builds to finish before i can even think about a new .308 :rolleyes:

I’d get a receiver on order right now if I wanted any kind of LR-308.

It sounds like either the lower or the mags are out of spec.