'Nother Stupid Q: Telestock Wobble?

Patient is an M&P. Any cure, or is this a get-used-to-it thing?

Can the existing config be modified to fix, or is some kind of switch-out required?

If the latter, must the entire assembly go (tube included), or can I just replace the plastic dealie?

I’m really splitting finickies here, since this is supposed to be a practical tool, but figured it wouldn’t hurt to ask.

Not really.

You could just by a VLTOR or Magpul (mil-spec) CTR stock, either will fit on your present recevier extension (buffer tube).

I can’t stand the wobble either, nor a wobble between the upper/lower. I run CTRs on all but 1 of my ARs with collapsible stocks, the 1 has a VLTOR.

Well thankfully, this gun is as tight as the proverbial cherry there (need a soft punch to move the rear take-down pin).

I see the thread comparing these - shall read in-depth.

Thanks!

ETA: So lemme try to get this straight. LMT is a mil-spec buffer/extension tube, whereas CTR is a commercial counterpart? They are different dimensionally? Otherwise?

Just want to make sure if I order something it is going to fit.

LMT, CMT, S&W, VLTOR and Colt all use mil-spec size tubes. Magpul makes the CTR in both a commercial and mil-spec size. The Magpul also has a tab that you can lock the stock up solidly, the LMT and VLTOR fit pretty damn tight already and don’t have this feature.

In the field I use to stick a piece of paper in it.

In used-to days, I would use a bit of electrical tape towards the back of the buffer tube to take out stock wobble. Cost = ~2 cents.

Or you could spend 75-100 bucks. Your choice.

I used 2 inch wide packing tape. It comes in different thicknesses and the thin stuff at work worked great. Two pieces… one just inside of the full open position and the other at the end. You can’t see it but it snugged it up nicely.

Think I’ll first try something along these lines as a stop-gap measure. Wouldn’t seem to hurt anything, and may turn out to be adequate.

All those aftermarket stocks look cool though, but now isn’t the best time for me spending-wise. Besides, right now I’d rather get more ammo!

Thanks folks.

Well I really appreciate the advice, but the tape pretty much didn’t work on my gun.

The stock fits closer coming off and on the tube than along the more forward part where it stays mounted. Hence, it would just barely clear a single layer of tape when first slid back onto the tube, but once moved forward to the normal range of positions was nearly as loose as without any tape.

Just to try out the feel, I wedged a couple thin pieces of rubber (similar to inner-tube material) down between the stock and tube to where they locked things up totally tight. Then while practicing alternating mounts from strongside shoulder to weak and back - boy, what an improvement! The stock just pops into the shoulder pocket and cheek weld with zero of that annoying jiggle. I’ll never go back.

Obviously with this arrangement though, I’m left with a fixed-length stock. My rifle case is long enough to accommodate it for the time being, but I can’t consider it a permanent fix so am back to looking at a replacement moveable stock. Would be cool to get a matching handguard and pistol grip while I’m at it, maybe in one of those colors like this web-page background for that cool two-tone look. Perhaps Daddy Day next month will be favorable to me…

I’ve never really understood the obsession some seem to find with “wobble”, whether it be in the stock or the upper. On a long-range precision rifle I guess I get it, but what’s to be gained on your typical “M4-style” carbine?

To me it just feels better without it.

But then, to me the factory pistol grip feels fine, which most people seem to switch out for something aftermarket. Guess it’s whatever-floats-yer-boat.

I just find any wobble very annoying.

To me it’s annoying like running in shoes that are too big and having your feet shift around in them. It’s cool too if it doesn’t bother you.

Maybe I’ve never had one that wobbled that bad. Fankly I’ve never even noticed it.

This is why God made Sully’s. :wink:

I agree - I find wobble in almost anything pretty annoying regardless of whether it affect function or not.

At someone’s suggestion, I got rid of the wobble between the tube of my ACE SOCOM stock and the receiver with teflon plumber’s tape. Can’t see it, cheap, works perfectly.