Is this the world's lightest 16" AR15 Carbine?

I have built an ultra-lightweight carbine using a Cav Arms lower and a Bushmaster Carbon 15 upper with a lightweight 16" barrel.

Before I added the G2 light and Elzetta mount, the complete gun weighed only 5 lb. 1 oz. without magazine (I’m waiting on the Magpul MBUS to shave off a few more grams.)

I’ve only shot about 100 rounds through it to date, but so far so good.

Does anyone have a lighter weight functional AR (short barreled rifles excluded) or can I claim the bragging rights? :wink:

Looks good. I like it.

-Add a Young manf. skeletonized bolt carrier and a hyperform free float handguard (allowing you to get rid of the handguard cap, delta ring, and barrel nut) and you will be shaving some more off. From there is gets crazy with Ti bolt carriers and carbon fiber wraped steel liner barrels.:wink:

Besides as an experiment, what is your reasoning behind this project?

I just had an urge to build a practical carbine under 5 lbs. - and I am this close.

With a few of LonghunterCO’s suggestions, I should get it under 5 lb., no problem :stuck_out_tongue:

Are you planning on putting a micro Aimpoint and a sling on it?

cut the barrel back and pin the FH. then bolt a small rail piece to the handguards and use an x300 for more weight savings.

except for the remote possibility that i’m gonna hump my AR around for days on end, i don’t personally have the need for an ultra-light rifle.

sweet

Long Walk AR
CavArms lower
A1 upper
16" pencile barrel (.625" FSB)
HyperForm ultralight handguard
Regular BCG
shaved bayolug
shaved sling swivel
Vortex FH

still left to do:
-replace BC with Young Manf. skeletonized BC
-barrel to be choped and pinned for AAC blackout mount
-cut handguard for sling swivel
-vent handguard
-add SOG graphite rail and light to handguard

So purpose of build: spend alot of time on the road with my job. Typically three day a week I am up to 150 miles away (as the crow flys) from home/family. This 150 miles varies from major metro areas to the middle of nowhere. In the case of having to hoof it home I was looking for the lightest build/Truck Gun that I could get without giving up reliability. Somethings that I was not willing to give up.
-Had to have a sling
-Had to have a light
-(no offence to the OP) needed to have aluminum upper
-Iron sights (I prefer the A1 upper)
-had to have an effective FH

Props to LonghunterCo for THINKING about what he wanted and why he wanted it just like it is.

It wouldn’t be my rig but I definately respect the thought that went into it.

Good luck

got ya beat :stuck_out_tongue: my game gun is right at 4 lbs (not including micro T1, larue mount, and pmag) but it has a 17" barrel plus a 3" comp (20")

but i like that gun.

whatever happened to cavarms?

whatever happened to cavarms?

A nasty bit of business with the BATFE.

I don’t know much about the details, but it happened a while back…

yeah, i mean, how was that resolved? did they get their inventory back? are they still in business? were there ever any charges filed?

Full details on that setup? 4 lbs is ridiculously lightweight!

I think that 4b is possible but hard to get to. We need picks and buid details.

my project was a similar strategy to the OP, but i changed up a few things. I got a relatively HEAVY stock and an extremely lightweight barrel. If I really wanted to go for lightest possible instead of well-balanced and best-handling, I could put an M4 plastic stock back on and shave another pound.

Balanced as it is, you can literally run this gun through a stage holding it like a pistol (only by the ergo grip) in an iso stance, arms fully extended.

specs
hamster carbon fiber upper
hamster carbon fiber lower
ABS carbon fiber barrel (over a rock creek blank, 17", rifle gas length, 1/7 twist, wylde chamber, titanium comp) (total weight 13 oz)
clark custom carbon fiber float tube, cut down (original shown in last pic was 6oz, but I’ve cut about 2/3rds of it off)
ace socom stock (by far the heaviest part of the gun, intentionally to help balance)
JP single-stage trigger (freakin awesome trigger)
JP low-mass bolt carrier (aluminum)
enidine pneumatic buffer
PRI adjustible gas block

total weight, including p-mag, aimpoint micro t-1, larue mount and everything is 4 lb 15 oz. but without all that, it’s right at 4lb.

(crappy pics, sorry)
with larue po’ boy magnifier and aimpoint T1

shows the aluminum barrel nut to which the clark guard is epoxied (i.e. basically cosmetic, not to be banged into anything. i use a magwell grip instead of a vfg)

the ABS barrel. expensive as balls, but hella cool. also, i had them clock the comp about 15* to the left, since i shoot left-handed. I have another on order at the moment that is 12" with a matching carbon fiber suppressor (together they weigh less than a regular M4 barrel) for a machine gun project.

the color in this pic is way off. it’s more of a cobolt blue, not a smurf blue

edit: this gun has survived a carbine class and a year and a half of tactical rifle matches. 1115 rnds total, mostly david tapp’s steel city match in birmingham. I bought an airbrush duracoated it myself.

Very nice!

No charges filed. As I understand it they’ve got some things back… computers and such… one of which was broken.

They’re operating. Their shop is in this old industrial strip. Part of it had burned at one time. The power to the shop is being redone… after the fire. So they aren’t molding any lowers right now.

Once they have 440 power they’re going to mold some lowers for submission to the ATF tech branch for approval, and then they’ll be off to the races again.

The Ti Bolts are just TiN plated, they are still steel.

He needs a Smith Ent Aluminum BC:D

No not those Gold looking things (bling/bling), they actually have a Ti bolt carrier.

http://www.brownells.com/aspx/NS/store/ProductDetail.aspx?p=25695&title=AR-15%20TITANIUM%20BOLT%20CARRIER

OK, I guess I don’t have the lightest carbine - nice guns!

Who has a link to the best place to get hyperform free float handguards?

Thanks!