I have been an adjustable gas block hater !

But I have a Noveske 10.5 with front sight base with a blow hole out of this world. I have many NFA rifles, and never have I even considered an adjustable gas block. But here I am.

I looked up old threads. Several were 2015… I want the most robust gas block. Least moving parts. I really don’t care if it’s adjustable, I just want it small. I dislike moving parts but again, here I am.

For those of you that have actually used them, what should I get.

PB

Syrac and SLR are the two I have seen/ head of.

I personally have a syrac gen II on my LR-308. Very easy to adjust, I have not had any issues with it. To keep it from carbon binding (have heard this can happen), I move it about 4-5 clicks back and forth after I shoot it just to ensure it doesn’t bind.

It is very easy to adjust and only has a detent which holds the screw in place. Based on my experience, I would recommend one or get another if I need an adjustable block.

Hope this helps.

I have both the Syrac & SLR. I prefer the SLR for its simplicity.

I believe Syrac is out of business anyway, so it’s moot point.

I guess that makes my choice for future purposes simpler…same for Pappabear

I’ve had best luck out of the SLR. But I don’t adjust them, I tune them to the lowest setting which the gun runs and leave them alone to never be adjusted again. Great for suppressor use with one ammo type.

Seekins Precision - It works and at $60, the price can’t be beat.

That’s how I found out. I had the Syrac Gen II first & was in the market for another AGB. After shopping for another one, I noticed everywhere showed OOS or discontinued so I started doing some research. They have a FB page saying they’re not out of business but there hasn’t been an entry for months.

Kinda glad though; it forced me to try an SLR & I couldn’t be happier. They do still get crusty, just like the Syrac, so they need a few turns every now and then to break it free.

I have an SLR on a rifle that has been fine. However in considering another adjustable gas block for a 10.5" barrel I’m actually leaning toward a custom tune gas port from black river tactical. Have you considered that?

Sent from my SM-G935V using Tapatalk

Markm already knows the answer to this common problem.

A BRT CustomTune Gas Port has no moving parts and threads inside your existing pinned FSB.

You can’t get more robust than that.

SLR is solid

I would go the brt route.

Sent from my iPhone using Tapatalk

If you want an “adjustable” GB that has no moving parts:
Baby Govnah - you drill it to size
BRT Micro Tune inserts - pick a size port

I use a SLR Sentry 6 and it does make me a little nervous.

Is that micro tune port an insrt? Ive heard of these

I have a Baby Govnah and found the fit on the barrel to be somewhat lose on my BCM BFH/Sionics 11.5" and Compass Lake 18" Douglas SPR. The lose fitment on the BCM barrel caused me some issues with failure to lock-back due to leakage. I had to ensure the set-screws were cranked tight/lock-tited down or I’d experience malfunctions. I was running about as close to “edge” of reliability as one would want too for disclosure (.067") on an 11.5" w/ A5A2 unsuppressed.

I’m interested in the BRT solution…

Pappabear, have you tried the Gemtech Suppressed Bolt Carrier?

I’m pretty sure Syrac Ordnance is either out of business or in foreclosure.

Ill dig into the SLR and the insert and pull the trigger on one of those.

Thanks guys

never bought off on the Gemtech BCG. Glad its working for folks.

PB

We offer two general solutions for over gassed barrels.

For barrels with pinned FSBs or special gas blocks, the Custom Tune Gas Port is installed into the existing block.

Installation does require basic mechanical skills such as drilling and tapping.

For fresh barrels, the Micro Tune Gas Block is a precision low profile gas block with the same port pre-installed.

Installation is as easy as any low pro gas block and ports can be exchanged while the block is disassembled.

Clint,

Thanks for sharing clarifying details on your product. As mentioned in my post above, I had a little disappointment in my MicroMOA gas block due to the has block having a bit too generous tolerances (for my liking) when fit over a variety of barrels from a number of manufactures. The MicroMOA is finished with a 0.750" ID and fit rather lose on my barrels. The BCM that it replaced measures 0.7485" and fits more appropriately on each barrel. What do you finish the ID of your GB’s too if I may ask? If a PM is more appropriate please feel free to message me that way.

Thank you!

I would go the BRT route, and since markm is already up to speed, it should be easy.