How much top end magnification is needed?

With the release of the gen2 PST line, I’ve seen a bunch of deals pop up on the gen 1 versions and was wondering if the 2.5-10 x 32 (FFP) has enough magnification on the high end for shots out to 800-1,000 yards, yet a reticle that is usable enough at the lower power ranges (~4x) for hunting situations? Or should I be looking for something like the 4-16x?

It will be for an 18" Grendel. Targets would be steel shapes or silohettes (tactical matches, not BR). Hunting would be done from blinds (deer) or spot and stalk or still hunting (elk).

Any suggestions?

Seems like 10X might be a bit light for 1k. I would be concerned with the 32mm objective also. For a K I think a 50mm would be in order. A 32 might get grainy on you.

I personally prefer the 4-16 range optics for what you mention. Not saying you cant shoot a 8 or 10x optic to 1K, but I do prefer the extra mag. All my hunting rigs also get a 16x on the top end with at least a 42mm objective. If I needed to identify any sort of Buck or Bull on the spot, its much easier to crank up the mag. I think you may be leaving a little desired mag on the table if you went with the 2.5-10.

I really like 4-16 for shooting my spr at 600-1000 yds. I used to have a 10x but it was not quite enough magnification in my opinion to get a precise picture, especially beyond 700 yards. Out to 600 yards it was fine. YMMV

Thanks guys. What about the reticle size at 4x with a FFP scope? Is it usable? If not, what mag range does the reticle become useful (large enough for closer shots <100yds)?

At 4x it is pretty thin, at 16x it is a little thick. Usable throughout but ideal in the middle ranges. I’m not that picky with reticles. I’d say offset irons or rds would be advantageous to use inside of 50 yds, give or take depending on the scenario.

Sent from my XT1565 using Tapatalk

ive got a 1st gen 2.5-10 and i dont think I could get accurate shots on a target at 1k. I have the gen 2 razor hd II 4.5-27 that I like a lot.

I used Bushnell 3-12 with Mildot reticle for 1k. Mag was not enough and Mildot was too thick, it almost covered the target. Now I have 3.5-21 hdmr with TRMR reticle, which is busy but I really like the microdot in the center

Some people would argue that more power is better at 1,000 yards, but I find that my Nightforce 5.5-22 x 50mm scope is more than I need at that distance. If I have to deal with a lot of mirage, I shoot at 15 power and have successfully engaged targets at 12 power. If I had to make the decision knowing what I know now, I would have purchased a 3.5-15 x 50 MM scope instead.

If I were in your position, I would consider the Viper PST Gen II 3-15x44 Riflescope. I think 15 power should be sufficient for shooting steel at 800-1000 yards and 3 power on the lower end would be practical for hunting inside 100 yards. A 44mm objective lens would be a bit better at gathering light near dusk or dawn than the 32mm you are considering.

10x at 1,000 yds is like no magnification at all at 100yds. If you’re OK with that, then go for it.

That’d be real iffy at a thousand; even with good eye sight. Keep in mind you’ll also want some really good glass. Not all scopes are alike when speaking of basic quality requirements for upper end of magnification.

For your use case something around 16x should work just fine.

that’s an interesting way to look at it.

It depends. My personal preference is no less than 16x for 1k and ideally 24x or more. 16x at 1k i have to really focus, and take more time to steady myself.

I went to a rifle class last year and they wouldn’t let you set your scope about about 12x. Of course some cheated a little but at 12x I could get 1k hits pretty easy.

I was shooting a 6.5 creedmoor. Also this is shooting torso sized steel so that will play into the equation.

If you are shooting paper or smaller steel I would go up to a 24x.

Sent from my iPhone using Tapatalk

Skip the Gen1 and get the Gen2. The price difference isn’t enough to pay for old tech (though I just picked up a PST 1-4x…).

You can definitely make hits out to 1,000 with 10x. What you won’t be able to do is spot your misses and see where you missed around the target. If you hit steel, you’ll hear it, or watch it move. But if you miss… you might struggle to see WHERE you missed to make any corrections to walk it in.

Consider 2 scopes for 2 different purposes that do their respective jobs well over one scope that does both poorly.

What tech does the Gen 2 have that the Gen 1 doesn’t?

Also, thanks for all the good responses so far guys.

I took my 1-4x equipped 12.5" AR (5.56) out to 500yds the other day on 12x18 steel and didn’t have much issue making hits. Even saw misses on a couple occasions. I do have pretty good eyesight so I’m thinking that a 10x on the top end would work. I’m sure 16x would be nicer though. I still haven’t pulled the trigger on anything yet.

On the gen1 PST line, is the glass on the 2.5-10x supposed to be better than the 4-16x version? For some reason I remember hearing something similar to that…not sure if true though.

A good rule of thumb:

At minimum, 1x of magnification for every 100 meters on any target equal or greater than 1/2 mil (roughly 20" at 1k).

That said, I don’t think enough emphasis is given to optic quality. I have some very high-end optics that top out at 8x that can stand toe to toe with any mid/upper-mid level 10x optics at the 1/2 mile range.

Noticeably better glass, daylight bright illumination, better reticle.