Glock 19 w/ RMR & Suppressor woes

I’ve got this little thing. I’ve had it for quite a while and have tried to cure some issues but maybe I could learn from M4C more easily.

I use this gun mainly for shooting bunnies (not kidding) and nightvision shooting when 5.56 rifles are too loud late at night. It’s However, it also has a recently discovered dual role of serving as my pistol for 2 gun matches which is where the issue have arisen.

  1. The zeros change all the time. There are essentially four - suppressed subsonic, unsuppressed subsonic, suppressed supersonic, and unsuppressed supersonic. The zero between unsuppressed supersonic and suppressed subsonic is more than 20" at 50 yards. It is insane. Aiming at a 6" plate roughly 20 yards away means a consistent miss unless holding for the shift. And since Failure2Stop and his buddies loves to shoot all pistols one handed :wink: - this is more difficult than it sounds. Is this amount of shift normal and have any of you done anything to alleviate it?

  2. I love the accuracy of this thing with subsonic (147gr gold dots) ammo and the suppressor. At 10 yards it’s ragged hole all day long. At 50 yards I can shoot coke bottles and 1/3 IPSCs at 100 yards are cake. But with supersonic ammo while suppressed accuracy really drops off. Almost 3" groups at 10 yards with 115gr Magtech and Sellier & Bellot. Is that normal?

Part of me feels the easiest way to solve these problems would be to just buy another G19 and RMR. Run this exclusively suppressed and the other from the holster. But that’s getting up there in funds or a duplicate.

With the amount you have invested in the G19 and RMR with a suppressor, it can’t be too much of a reach to get another setup and dedicate one to carry. In fact, that’s really the most sensible solution I can think of.

I can’t speak from a position of authority regarding your zero shift, but it makes sense to me.

Not sure about accuracy, but have you tried comparing the same bullet sub/supersonic? Going from good Gold Dots to only decent Magtech and S&B may be part of the issue, especially if you’re switching from HP to FMJ.

Have you tried any 124gr ammo and what were the results?

Perhaps you could find a happy medium there.

If you like the accuracy of the Speer Gold Dots then try their Lawman FMJ for target ammo.

Also, when was the last time you replaced the RSA? It could be getting weak and exacerbating Glocks notorious premature unlocking.

It is not uncommon at all to see significant zero shift in a pistol between suppressed and non-suppressed groups. To my knowledge there’s not much to be done about it.

As to the disparity in groups with different ammo types, that’s not all that uncommon either. Find the ammo your gun likes and run it. Just a hint…if it groups well with 147 Gold Dots I’d start with a 147 FMJ of some type to see if that shows improvement over the 115 gr. fodder.

What can are you running?

Velocitas, Opprimere,
Violentia Operandi

X2. I’d personally stick with 147gr. loads and set your sights up accordingly. That way you only have an unsuppressed and suppressed zero with the same ammo. Buy a case of Speer Lawman 147 and give that a try.

I zeroed my RMR with 147GR HSTs through my G17 with a Silencerco Osprey and the shift is very minimal out to 50 with or without the can. I switched that gun to a steady diet of 147 fmjs as well for this reason.

I was initially shooting 115s without the can and 147s with it and the shift was similar to what you’re describing.

I opted for a G17 set up exactly like my G19 to run with a can full time with 147s. The cheaper route would just be to switch up the ammo you’re shooting through it so it is all one weight. You can find speer lawman 147 which has been very consistent for me for around 220 per 1k shipped.

Octane 9

I’m noticing a trend. I’ll buy a case of 147gr Lawman asap. This isn’t small bore rifle shooting, but being >6" off at 20 yards pretty much makes shooting unsuppressed useless and that is unacceptable.

The RSA is factory with the gun. Probably 4,000 rounds?

Shoot unsuppressed 147 gr standard pressure ammo and compare to 9mm NATO. POI will be different obviously. I wouldn’t waste money getting another gun, I would just get the same ammo. Sight in for can if that’s more important or sight in without if that is. Right?

Bro, I’m betting the rifling in that barrel is configured specifically for 147.

I think you’re a genius fam.

I have a 1:16" twist barrel. I think that’s why the 115gr stuff shoots worse out of my match barrel/RMR setup than my bone stock 20 year old Gen2 with irons.

There’s no other explanation I can think of.

We’re a relatively smart group of deplorables :wink:

RSA’s cheap AF brah:
https://store.teamglock.com/gun-parts/glock-recoil-spring-assembly-g19-g23-g23p-g32-g38.html

You da man!

I paid over 20 for my last one and I desperately need another. Those prices are faaaaaaantastic.

Praise be to Kek the Holy!

When I found the store on the Glock homepage and saw all the prices I was like Midway who?

We’re like glock autists…

Ok, which one of you ordered all of the Speer Lawman at SGAMMO last night?

I put it in my cart but because I ordered a 6920 from Grant yesterday I decided to sleep on it. Woke up this morning and its all gone. :mad:

Big A, thanks for the link to that store. Might grab a few G17 trigger bars for my G19s while I’m there.

Shit, I was going to grab some.

Honestly, id just shoot 147 excluseively.
What silencer is it? Can you adjust poi with it?

You know how to index that Octane right? When it is on the gun just pull it forward and twist. There are like 5 settings and they really do change point of impact.

I was late to the party. 147gr in my 19 always seems to get me better groupings, regardless if it is running through a suppressor. Was going to start there.

As is, it sounds like you just need a case of beer to provide targets. Bromancery solves yet another firearms problem.

One love.

edit: is my google-fu weak or is that (teamglock) one of the better prices for snapcaps/dummy rounds going?

Sadly they don’t sell trigger parts :frowning: You’ll have to keep going to the usual suspects for that.

Probably a good idea from a Bubba liability standpoint though…