Essential Arms Lowers - review

Well, as I posted in another thread, a few weeks ago I ordered 3 EA lowers to build identical AR’s for myself and my two toddler sons. I figure by the time they get grown (and they won’t get them until the are grown) the AR could very likely be long since banned and it’d be cool for them to have a piece of firearms history. I think all 3 of us having identical AR’s with sequential serial #'s would be extra special, cool, sentimental, whatever.

I recently bought a new Double Star DS-4 carbine and really like the VERY nice roll marks on the lower and they are only 25min from where we live so seeing the Winchester, KY on the side makes a good ol’ KY boy proud too. I tried to find DSC lowers, but they weren’t out there - at a reasonable price or time frame with the sequential serial #'s - that I could find anyway. I seen many good reports on several forums about the EA lowers and their good availability so I ordered 3 in the Tough Coat finish, which is baked on over top of the hard anodizing from what I understand.

The lowers came in this week and I was pleased to see they look very nice. They are absent of any mold flash. They don’t have the molding ridge along the center line of the trigger housing like my DSC has, but they do have some light tooling marks in there but the finish hides them well and you have to get right down on the area to notice. They have a nice smooth radius on the underside of the buffer extension and only a minimal trace of a tool chatter mark on the underside of the front take down pin bosses. The roll marks text is a little light on a letter here and there and the FIRE and SAFE on the right side of the lower is not as deep as the left side of the lower - this is common on all 3 of the lowers I got. The roll marks don’t look bad by any means, just don’t look as good as the VERY nice, deep, sharp text on the DSC lower.

I have some background in machining, CNC programming and CMM programming so I understand a little bit about how to layout and measure a part for dimensional accuracy. Having said that, I only have a set of digital calipers and micrometer at home - a surface plate and height gauge or even a small CMM in the garage would be sweet, but not very practical for me. The calipers work good enough to make due.

Going off a lower blueprint I found online, I checked every dimension I could with the tools I have and found the lowers to be in spec. The exception being the trigger slot width being .002" over spec, the width between the front takedown bosses .002" over spec, the rear takedown detent hole .004" over spec, on 2 of the lowers the distance from the front takedown pin hole to the hammer pin hole was .0007" under spec and on the other lower the distance from the trigger pin hole to the fire selector hole was .001" under spec. These measurements between holes were taken using the standard pins that come in a LPK, so that really doesn’t concern me a great deal since the pin/hole fit is not a press fit and has some “slop” or tolerance built in.

EDITED To better explain what I mean by the hole locations being “out of spec” as I measured them. I re-read my post this morning and can see how someone could be left with misunderstanding what I meant by saying the the hole locations being out of spec by .0007" and .001" didn’t concern me a great deal. (when measuring with calipers and LPK pins)

The Trigger and Hammer pin holes have a spec of .156" +/-.0015".
These holes in the lowers I have measured .1565" on 2 lowers and .157" on the other lower.
The Trigger and Hammer pins that I was using out of a Double Star LPK measure .154".

**So, with the .154" pin in the holes .157" in diameter, the pin would have been pulled off-center in the hole .0015" while I was “pulling” on it and the front takedown pin with the calipers to measure the distance between them. Factoring in the true pin size and true hole size and adding that difference back on top of the measured distance between the two pins, the true center-center hole measurement would be “in-spec” per the lower print. I guess it is my fault for not explaining this in the begining, or I should have just said they are in-spec and could have avoided some possible confusion.

Now I am not saying these are “top-shelf” or “THE” best lowers on the market or anything remotely like that. Just that, IMO, they appear to be very well made lowers. Having said that, understand that at this point these EA lowers and my DSC lower are the only ones I have ever had in my hands and my eyeballs on. So, take that and these pics with that in mind.

Now I just gotta pick up some BCM middies to put on these suckers :smiley:

Left side

Right side

…

they dont get too much better than that, but do get a hell of a lot worse. update us when you install the LPK, if you would. i’ve placed bids on many EA lowers on gun broker, but never more than 130. some have even been won at like 135- i’d probably be inclined to up my max bid after seeing your review here.

I got these straight from EA at $105 with the TC finish. Ordered on 1-19 and picked up from my FFL yesterday. Unless they have raised their prices since then…?

…

neg- i never explored that option. good lookin out, i just might place an order.

If ya do, ya gotta call first thing in the morning when they get in to get through on the phone. May have to try 5 or 10 times.

…

I myself bought 13 of these back when they were $76 a pop. I really like them.

All but one were GTG. The only issue that I had with the one was the rear take-down pin detent hole was drilled “undersized”. After a few careful moments with a hand held drill and the appropriate bit everything was ready to roll. They were all finished nicely and the optional colored coatings are of good quality also.

Some time here in the future I might buy a few more if I cannot find some “Mega” Brand lowers for a comparable price…

They were a real steal back at $76 a pop, and I would/will still buy them at $105 each…

—>APB

PS:

One thing I did notice was that when trying to use P-Mags I could never get the mags to lock in without altering them a bit. They would just barely almost lock in, but the raised rib like features on the P-mags would contact/stick in the bottom of the magwell and prevent further insertion of the mag. After some rotary sanding on the mags they inserted, locked in , and dropped free just fine…

I currently have 3 of these built, and have been very happy with them so far, especially since I paid 85.00 each for them shipped. They have gone together as well as any of my stag lowers, way better than the oly I had (note, “had”), and better than the superiors i helped my buddy put together. 4 of the guys I work with have them also, and I either helped or put them together as well. They lock up tight with my LMT and CMMG uppers, and am waiting on a BCM middy to replace a bushy upper I have on one. I am probably going to put another order in soon. These are still a very good value at this price point.

Jeff

A friend just received three last week, one of which has my name on it. Now if I can decide what to build.

I ordered 1 about a week and a half ago. It took 2 faxes and about 50 phone calls to get through. I can’t wait. They said 2-3 weeks before they would ship. I had a complete upper sitting around that I was thinking about selling then thought what the hell, I’ll make it a complete. I will post pics and comments when it arrives.

I just went to their homepage and checked them out. They’re still listing the stripped lowers for $105.

Essential has high an low shelf lowers. They also have anodized and ones with their “tough coat” finish. I’ve build a number of them since the election and have found them all to be in spec and issue free.

Getting them by telephone has been a bit of a challenge. I needed to dial the number 37 times to get through to them.

I’ve been reading about these for a while, you guys pushed me over the edge. The product in the photos at the top of the thread remind me of my Spike’s lower, only a helluva lot less expensive.

So I called this morning and ordered three. I have a BCM 16" M4 upper arriving tomorrow, and I am hoping to pick up a BCM middy when they become available. The third one? I’m sure something will come up.

I just called, 1515hrs eastern. I got right trough, orederd two basic hard anodized for $100 each. With credit card surcharge and shipping to my FFL, $222.00. They said they’ll ship within two weeks.

This is my first post, is there an intro thread I need to post in?

I have used EA receivers for years.The original ones were investment cast and had a “rougher” finish,almost like a sandblasted surface,but were GTG.The new forged ones have a smooth finish and are pretty nice.I only had one that had the rear receiver extension threads slightly out of spec and were easily cleaned up with a quick thread chase.

Did my first build with an EA lower, everything went in place like it was supposed to and stayed there. One of the best values in lowers

I read through and did not see it, but are these lowers to mil-spec dimensions or commercial dimensions.

What’s the differences between a mil-spec dimension or commercial dimension lower?

This is the print I compared these lowers to…

http://www.ar15.com/content/manuals/lowerBlueprint.pdf

…

Which is based off a 93 colt lower, it’s what I check my lowers against as well.
Surprisingly…I have a DPMS lower that matches up pretty close in most aspects (.001 in most cases).

I was thinking the main issue might be with the trigger pin dimensions thats why I was mainly asking, I thought it might sort of restrict someones selection in aftermarket triggers. :confused:

you’re one of four people whose first post is in this thread… odd.

you can introduce yourself in a seperate thread and tell us about yourself, or you can just start pontificating straight off the bat like everyone else :slight_smile:

welcome to M4C