Converting Kimber 5" 9mm to .38 Super

What do I need to convert a factory 9mm to a .38 Super? I think I could do it with just a barrel and magazines. In fact, wouldn’t it be possible to do it with just magazines if I wanted to have the factory 9mm barrel reamed to .38 Super dimensions?

TIA

Without looking at chamber specs, a GS fit barrel in 38 Super would be .010-.020 short of SAMMI specs for 38 Super and probably still too long for the .857 (?) of a 9mm so you would be headspacing off of the extractor. That isn’t taking into considersation the Super Base Dia.

OK, you made me grab the book;

9mm Head Diameter .394 38 Super Head Diameter .406
Body Dia. .391 Body Dia
Bell Dia .380 Bell Dia .384
Max Case Length .754 Max Length .900

So, let’s call a GS fit barrel with a short chamber at .875 with a bell diameter of .384 at that length and tapering from .406 and the same with the 9mm it looks as if it would be abit loose.

You could probably just get by with a barrel and mags and a new front sight unless you have adjustables. Some 9mm mags have a spacer in the back of the mag tube since 9mm is shorter than 38 Super, 9.21, 23 and it keeps the bullets stacked better in the mag.

For the outside cost of a conversion, it might be cheaper to go with something like a used SA 9mm MILSPEC. I missed one at auction and built my own but they around in the 6-7 neighborhood. If you have someone outside install the barrel, make sure they are familiar with 9mm 1911’s and getting them to function reliably, perticularly if it is a ramped barrel installation.

3-5 mags 150
barrel 150-225
Barrel Installation 200-300
Front Sight 10
Dovetail for Front Sight 30-50

With the back spaced mags you might need to change out the ejector to get reliable ejection, perticularly in function drills. The back spacer speeds up the next cartridge in the magazine rising when hand cycling a round out of the chamber. The next round in the mag pushes the cartridge on the breech face up, missing the ejector unless you pull the slide back quickly enough before the shell gets pushed out of the way of the ejector. If cycled fast enough or without a magazine in the gun, the pistol appears to operate normally but slow down the sequence of events with a back spaced mag an instant double feed jam with a short ejector.

When building a 9mm single stack I trimmed a 9mm extended ejector like I was taught to trim up a 45 and discovered this problem. I got a new ejector but haven’t really found the need to install it yet. It cycles fine and ejects consistantly as long as it is sprung right for the loads (10, 11 Pro, 12 and 14 lb springs).

Right now I’m working on a bullet shape feedway jams. Some projos it feeds like a sewing machine 115-125 ball, 124 TC while others tip over and jam on a full mag, drop it down to 8 and no problems. I know, just put eight in the mag and problem solved. I might have to change the P/C ramp angle to get reliable feeding with all bullet shapes.

I’m using Wilson ETMs right now and looking at trying some other mags.

Other way 'round. I have a 9mm, I want a .38 Super.

Yes, I think that is feasable with some minor tuning of the ejector. I would seek the advise of a good smith on reaming the barrel out. It looks like the numbers will work but here is some previous posts over at 1911.com. One comment by George Smith or EGW said he wouldn’t ream a 9mm chamber to 38 Super, 9x*.* if it was larger than .392.

http://forums.1911forum.com/showthread.php?t=176403&highlight=Converting+super[http://forums.1911forum.com/showthread.php?t=51425&highlight=Converting+super](http://forums.1911forum.com/showthread.php?t=51425&highlight=Converting+super)

George is a good guy and knows his way around 1911’s… He is usually pretty accessible if you give him a call at his shop.

Would it not be a better idea to simply have a proper 38 Super barrel fitted?

Ejector and extractor tuning, new recoil spring, maybe a new front sight.

When I was looking for a new recoil spring for my Colt Gov’t in .38 Super, Wolff listed 14lbs for both the 9mm and .38 Super.

I went with a 16 lbs spring and it’s been running great so far.

I just checked the ejector on mine.

It’s a Colt Commercial Gov’t Model from 1947. It has the same non-extended standard length ejector that a M1911A1 has, which stands to reason, as the overall length of the cases is about the same.

IIRC the 38 super is a semi-rimmed cartridge, so the extractor hook might be shaped a little differently than one for a 9mm. Just another thing to think about.

My experience is the other way around. However, I think it is fairly simple in either direction.

People talk about the differences in the extractors. 3 times my experience has been that the extractor worked fine with either cartridge. Not saying a minor tweak won’t be necessary, just that I wouldn’t expect it.

The 9mm ejector will be too long for the .38 Super case. Not a big problem, I shortened one and it ejects just fine.

Your old spring is probably fine, unless you want to fire some of the really hot .38 Super loads. New magazines will be necessary, though.

I have converted a .38 Super Gov’t model, Commander and Delta Elite to 9mm successfully, though I only consider them suitable for range use. No major problems. I wouldn’t expect any major problems going in the other direction.

Quick question, why do you want the Super over the 9mm?

The velocity numbers I have seen have been…unimpressive.

And Darned close to +p+ 9mm