chopped carry handle buis

I’m looking at partaking on this endeavor with a colt carry handle I conned off a guy at my department. I’m looking at some input from some of you out there who have cut down a carry handle into a buis. I know there is not much other than cut the sucker off but maybe what works best and ways to touch it up after the fact.

Article on TOS:

Let’s face it some of us don’t condone doing this, but it’s a great project if you’re on a tight budget and you have an extra carrying handle laying around. I recently made a thread regarding the chop and someone asked for a How-To, so I figured I can give it a shot.

Tools you will need:

  • Spare A3 Carry handle
  • Metal Cutting Hand-Saw (Stanley 6" 9$)
  • Sand-paper (150 Grit 4$)
  • Primer Spray Paint 3$
  • Flat Black Spray Paint 3$
  • Painting tape 3$

Note: You do not have to use primer and spray paint, if you can anodize it. Surprisingly the flat black matches very well to my reciever (Mega and Bushmaster), and I’m positive it will look fine with any other. If you have a dremel and other power-tools to help you with the job, then more power to you!

Warning: When doing the chop please wear protective clothing and a cover over your mouth and nose. Aluminum flakes can be TOXIC if inhaled or on the skin.

Step one: Preparation

The carrying handle is layed out, you want to apply tape in front of the area you are about to begin cutting. I recommend starting from the top of the handle, as there is less mass to chop through. You want to begin the cut directly in front of the beveled region in front of the sight aperture and straight down.

Step Two: Upper Region

I recommend making two incisions on each side of the rear sight guards, if you begin the cut with both edges simultaneously you will most likely begin sawing at an angle. Once you have begun the cut, you can remove the tape. Every couple of millimeters you take off, run some water over the cut to remove flaking. It will be extremely difficult to cut with aluminum flakes in the way.

You’ll begin to notice that the straight cut leaves a protruding region to the left and between the rear aperture and elevation. Not to worry the sand paper will smooth everything right out.

Once you get past the rear sight guards, you want to start cutting diagnolly if you’re using a hand saw. Notice I am not cutting directly downwards. Cutting in a diagnol will make it easier to finish the cut, since you are chopping through smaller mass.

The top of the carry handle should now be cut, you should be able to see the protruding region in this picture.

Step Three: Lower-Region

Now we begin cutting the lower region. This time you want to flip the carry handle over, and cut in front of the rail arm (Okay I made that up, it’s the piece that holds on to your picatinny rail ). Set some tape in front of the cut again so you can begin a straight chop. Again I recommend cutting it diagnolly or vertically!

Step Four: Sanding

Now we can begin the sanding. I used hand sand-paper and elbow grease. I layed a piece over my table and began grinding, the now, buis against it. Once I got a steady and smooth surface I began doing a couple of touch-ups to the rough edges with the sand paper by hand.

Step Five: Final Touches

Now we lay down a layer of primer. I used the “Rustoleum” brand. If you’re a sloppy painter, then you can apply two layers and use 500-1000 grit sand-paper to get rid of blemishes. I didn’t bother painting the entire BUIS as to keep most of it’s finish looking exactly the same. I covered the entire thing with tape, and left the area that was cut and sanded only to be painted.

The next morning we apply the flat black, which was also “Rustoleum” brand. I put 2 layers of black, to prevent chipping and exposed aluminum with scuffs.

Pics were dead

hacksaw
dremel
metal file
masking tape
grill paint

apply as needed :smiley:

That’s the post from ARF I was talking about, Kornbread.

How did you find that, Ridge?

On TOS’s Ar-15 section, under Optics, it is a sticky.

Thanks for the reply. It makes me feel a littel more warm and fuzzy to get a second opinion before I go all tool crazy on something.

handsaw? i’d start with an angle grinder with a cutting wheel to chop it off(a dremmel with a cutting wheel would also work), switch to a dremmel with a sanding wheel to bring in the nubs and/or burrs left from the grinder, and smooth that out with some 200 grit all-purpose. finish with birchwood casey’s and put it on the gun. i’d guess 20 minutes from start to install, not rushing

wont it be easier to get an LMT buis

It takes almost no time to cut through it with a hand-held hacksaw (we’re not talking hardened steel here or anything) , and that’s a tool that 99% of people will have vs. an angle grinder that may be a little less common. Not to mention the potential for an angle grinder to get away from the person using it and over-cut, vs. the ability of the hacksaw to make small corrections as you go.

  1. He’s already got an extra carry handle for free, and.

  2. LMT is casting their BUIS bodies now. :rolleyes:

  1. homemade stuff is nice :stuck_out_tongue:

oh… that’s a good idea.

by the way. how do I tell if mine is cast? or forge?

My thought as well. Sell the carry handle for enough to get a LMT BUIS.

Didn’t you ask this before when you first got yours? I thought your question was answered back then.

spamsammich,

it was never answered. in fact until now, I don’t know what cast looks like. or cast marks if there are any. I just assume that forge will be heavier than cast. but again. I have nothing to compare it with.

Take it down to your PD garage/ fleet maintenance shop, and hit it with a grinder. It takes 30 seconds. Touch it up later on with alumablack, and you are all set. I also did a few with a bandsaw and benchgrinder, but cutting with a regular hacksaw or dremel will work easily as well. Any black spray paint will work, you can spray it in a cup and slap it on with a cotton swab if you don’t want to spray the entire unit.

The below one was an aftermarket CH that I did with a saw, and then did a quick cleanup with a bench grinder. Its a simple and quick deal no matter how you do it.

One thing I do is keep the supporting/ clamp bar a little long for greater surface contact.

It would but after my spending spree last year my better half has me on gun stuff lock down. Thought that I would give this a try for an extra buis.

There is no reason to pay $100 for an LMT buis, if you have a carry handle laying around.

“IF” i were going to pay money for a fixed BUIS, I would buy a Larue instead.

I’ve been considering this for awhile. Looking at Sticks I am gonna go for it.

6 months ago I would have agreed with you (and did, with my wallet) but today I’d go with the Daniel Defense.