Black Hills 5.56mm 77 gr TMK and 69 gr TMK Review

I got the chance to try some Black Hills 5.56mm New Factory TMK ammo in 69 grain and 77 grain bullet weights. We run a 77 gr SMK house load in .223 pressure/velocity, so I thought we’d use that as the baseline, and go from there.

I initially wondered why they would take the 69 gr to the 5.56mm loading, but after our first time running the ammo today, I think this load is going to be something very impressive.

The ammo comes in the same red/black box that Mk262 does with the nice plastic insert that protects the ammo. The box insert holds the ammo by the neck to protect the round and the bullet. Both of these loads come in LC brass with primer crimps and the visible annealing iris.

We only got to fire a box of each load today… getting the administrative stuff out of the way… (POI check, chrono, etc.) The POI seems to come up very slightly for both loads. 1/2" high of POA which makes sense due to the higher velocities. We used the Magnetospeed today: Pappabear with his 20 inch 5R Rem 700

Using the above pictured bolt gun, we captured the following:

The 77 gr logged 2825 FPS with an SD of 10.

The 69 gr logged 2969 FPS with an SD of 12.

Both very nice velocities and standard deviations.

At 500 yards, (we’ll have to confirm this again) the 69 gr appeared to have a little edge over the 77 gr. Both of the loads creamed our SMK come up of 3.5 mils.

The 77 got there with 2.9 mils, and the 69 gr got there with an even lower 2.7 mils. I hope to be able to figure out at what range the 77 takes over, but I was really impressed with both at 500.

At 640 yards, (fighting mirage by now) Both rounds were getting good hits with 4.0 mils of come up. (impressive compared to my .308 175 gr SMK 20" bolt gun come up of 5.0 mils)

At 900 yards, the 69 gr load was getting on steel with 8.5 mils of come up. (vs. 10.0 using a 77 smk .223 load)

At this point, we were miraged out and getting hot… so we’ll get back after it over the next several weeks. But so far, it’s been easy to get quantifiable performance improvements over standard velocity ammo.

This should be an interesting thread to follow. I remember Sinister also having kind words for 69-grain loading as well.

I got some of that 69-grain stuff a while back, but have not had a chance to run it through my BCM Recce-ish carbine.

The 69 blew me away for sure. Our spot is often a mirage and wind torture chamber. We have a lot of distance, but it’s challenging and even frustrating many days.

That sounds the perfect place to shoot. :slight_smile:

Very happy to see this thread. I’ve wondered how the 69gr TMK would do. I’m generally limited to about 1/4 mile, so I wonder if the 69gr load would be hard to beat at that distance. How did it compare with wind drift to the 77gr load?

I just don’t know yet. I hope to be able to make that assessment, but we literally watch the wind ribbons reverse in the same 5 shot string. If this continues, we’ll have to get two guns (with mil reticles) running at the same time.

When did markm start liking Black Hills Ammunition?

I must have missed something.

Yeah… I kinda got burned out on the benchrest dogma that’d I had subscribed to for a period in my life. Specifically when I had some of those kind of fags (on this site) telling me that what I was doing was WRONG… even though I was gettin better than half MOA results.

We ended up shooting some factory Mk262 from Black Hills. And on that day it kicked my ammo’s ass on S.D., velocity, etc. So we’ve been shooting some B.H. 5.56 ammo with good results.

When you let the bullets tell the story, and let go of what the calipers, gauges, and instrumentation are saying… you make better calls. I’m not letting go of my .223 77 gr OTM load at all. But I will post quantifiable results… even when my hand loads get beat. :wink:

It’s good to see you give Black Hills a shot, as long as you don’t go all out full gueer and start using Sprinco springs and LWRC piston rifles. :no:

Another notable, but should be obvious with the SD’s Mark posted, the ammo shot sub moa. It also shot sub moa out of my SPR Reece ish guns. One has a Centurion barrel and one has a NOVESKE. Both 16 inch tubes.

I think my Noveske is so nasty dirty it took about 30 rounds burnt through it before the groups tightened up. It didn’t shoot great, so I went back to our house load, shot like shit, …asked Mark shoot it a while. Then at the end, it shot a nice sub moa group. Time to bore swab that bad boy.

I had to put some Springcos into a few of Pappabear’s guns. I thought about throwing them out and subbing correct springs. :wink:

Wow, that’s bad but Pappabear has always been a bit more of a hippie than you… Are those the Sprinco springs that that “enabler” Iraqgunz gave you guys?

I only buy Colt springs. :happy:

Pappabear, did you get a chance to chrono it out of your 16" guns?

Have you guys had a chance to test any of the other popular faux MK262 loads? I was all about my Defender stuff but the velocities seem a little low compared to the real thing…

We are going to do that next just confirm data. But we did it on the first run of BH stuff and it was solid.
We will run 16, 14.5, 11.5, 10.3 and post.

We were thinking about doing them with and without cans.

PB

All he would have done is put them in his guns. He loves my Sprincos , I saw his eyes when he looked at them. Can’t fool a Pappabear.

Be careful there Jr.

No worries… That’s about as accusatory as I get. :smile:

We haven’t. When you can load your own, it’s not often that you buy very many factory loads. If I saw some of the options locally, I’d pick up a box or two to play with. Oddly enough… I hate going into gun stores.

556cliffy, Just shut the **** up. It’s not as accusatory as I get. You little bitch.

PB