Barrel nut wrench for installing LaRue handguards

Well, I just got in a LaRue 11.0 that I ordered a few weeks ago for a personal build on a BCM middy upper. Come to find out that the barrel wrench I have does not actually fit the LaRue barrel nut.

LaRue is out of stock of their barrel nut wrenches. What can you guys recommend for installing LaRue barrel nuts?

Thanks!

http://216.23.214.70/lt/handguards.html

This is what I use:

PRI barrel nut wrench perfect for installing LaRue, YHM and other non-steel barrel nuts without damaging them has 5 longer pins that engage the holes in the barrel nut instead of 2 or 3 short pins if using a DPMS or USGI wrench

It’s it the tool sticky I posted a long time ago.

Nice, thanks! I just ordered one.

And while we are on this topic, who do y’all like for a good torque wrench?

I ordered one of those PRI barrel nut wrenches a couple of weeks ago based on gotm4’s sticky recommendation. It fits the Larue barrel nut perfectly. It doesn’t seem to fit a standard barrel nut, but I’ve got another wrench for those, so it doesn’t matter.

I’m working on one too. :smiley:

Not cheap…Snap On. :smiley:

For anything other than DD Lite Rail/RIS II rails (I torque them exactly to 70ft lbs) I rarely use a torque wrench. I can tell by hand when I’m over 35ft lbs and can tell when I’m up near 80ft lbs.

Which Snap-on torque wrench do you recommend, which extensions/tool heads are helpful for installing fore-ends, and where do you recommend buying Snap-On tools?

Thanks!

Save yourself a bunch of money and buy this Craftsman one. A Snap-On one will cost you more than twice that price.

http://www.sears.com/shc/s/p_10153_12605_00944597000P?keyword=torque+wrench

Thanks!

(And now for what could be the dumbest question of the day) I have a Torque Wrench in In-Lbs is this a 12 inch pounds=one foot pound conversion?

I’d save that one for inch lb stuff and get a bigger 1/2 drive foot lb torque wrench that goes to 150-250ft lbs.

I will but that is all they had a work so that is all I have for now. I found a convertor
http://www.boltscience.com/pages/convert.htm

35 Ft lbs. = 420 in lbs.
80 Ft lbs=960 in lbs.

I’ve never seen an inch lb. torque wrench that went up to 420 in lbs nor 960 in lbs.

That product has 2 stars out of 20 purchasers :confused:

That’s disconcerting, I’ve never had any trouble with Craftsman.

I have two (a 3/8" and 1/2" drive Craftsman digitork torque wrenches) at by dads place in NC, since they’ve been at his place for 10yrs I just gave them to him. I use a 1/2" drive dial type Snap-On torque wrench for big stuff and a 1/4" drive Snap On clicker for small things like carrier keys but need to buy a 1/2" drive ‘clicker’ type to make it easier than trying to read the dial although the dial is more accurate. I may buy one of the Kobalt ones from Lowes.

http://www.lowes.com/lowes/lkn?action=productDetail&productId=148619-1074-22505&lpage=none

How do you purchase Snap-On tools? I don’t mind spending extra money on quality tools.

Through their website or from the local franchise guy. Ask any mechanic for the local guys route near you. Any mechanic at just about any car dealer will have the guys contact info.

But all the mechanics around here speak Kurdish and Arabic :eek:

(Thanks for the info :stuck_out_tongue: )

That’s okay, I don’t think much on an AK or RPG needs or has a torque spec. :stuck_out_tongue: