Assembling bolt / dumb question

Please forgive me but it has been a while…so I need some simple instruction. I just recievesd my new black insert, spring, and crane oring and new extractor…No instrustions came with parts…My question is this. Holding the bolt in my hand what is the order of the way the parts are installed???
Does one install the black insert, the oring then the spring, then the extractor??? then install the pin, or is there a different order…Some folks say with the new spring you don’t need the oring…Thanks in advance for any and all help…Pics would be nice too…

Pull out the old spring and buffer.
Put in the black buffer and spring.
The wide end of the spring goes into the buffer recess.
Make sure it is fully seated and not crooked.
The experienced armorers have sneaky little tricks to get them seated correctly. I don’t know the tricks so I just swear a lot while flinging the spring accross the room at random intervals to remind myself why I am not an armorer.

Do not worry about the O-ring unless you have continued extraction issues.

or do you just disgard it…sorry I am so dense…

It goes around the extractor spring.

anyone have any pics…The mental imiage I have is…I drop in the black insert…make sure it is seated…put in the spring, then put the oring over the spring, then install the extractor then the pin…That sound about right???
sorry I make it harder than it has to be…many thanks for all the help…

I’m with F2S on this. Leave the O-ring out unless you continue to have problems with extraction.

Simply place the buffer within the spring (all of ours have them included already) and then seat it into the extractor. Then use a small pair of pliers and gently clamp down and it will set into place. Then put the extractor into place and reinsert the extractor pin.

Out of curiousity what type of weapon (make and model) are we talking about here?

I know is is another site but it might be able to help.

http://www.weaponevolution.com/forum/showthread.php?t=341

extractor was worn pretty bad only 1000 rounds…got the kit from BCM…just not sure how to put it all back togeather…things inside the bolt were pretty beat…sure wish I could get a pic…a gunsmith I am not…I have a spare bolt and cam pin…just doing some maint. and want to get it right the first time…firing pin looks good.
thanks for the help guys.

Got er done…shoots fine…many thanks guys…using Mobil one 5-30 synethic…that is good enough right…running it wet. This baby rockes never a jam…FTF…zip…I was just amazed when I saw the wear on the extractor…no metal case ammo ever saw this new colt

Those pics at weaponevolution are the first time I’ve seen an O ring installed… I’m no engineer, but can someone explains what it actually does? Looking at it I can’t figure out how that helps…

supplements spring tension. Just think about it for a bit, it’ll come to you.

If you install one onto your extractor spring it will become apparent that it increases the tension on the rim of the extractor.

The 0-ring increases extractor tension up to about 400%.
If you’re not having extraction problems it isn’t needed and can cause feeding problems especially when the buffer spring gets weak or the carbine is dry and dirty. Don’t fix it if it isn’t broken.

Lately I am seeing and repairing a lot of guns which are ‘short-stroking’. About 1/2 the time it’s a lose carrier key or lose, junk or just misaligned gas block. The other 1/2 of the time it’s too heavy of a buffer, too high rate of a buffer spring, LMT enhanced carriers on guns with small gas ports with small barrels and .223 pressure ammo combined with one or all of the above. Some people are just throwing parts into their carbines thinking that they need this or that. They aren’t understanding how or why such and such part works or how these things effect the system. A little knowledge can be dangerous.

Exactly right Robb. I get emails all the time from people that say “I took your advice and installed an H buffer and now my gun has problems”. Whoah there skippy, my advice? When I ask them what problems they were having with the gun that they were trying to correct with the heavier buffer they say “none, I just wanted to make it ‘better’”. :rolleyes:

That’s why I think the explanation of features in the Chart, your “what do I do now” thread, and an article I’m finishing up for Combat Tactics which is a variation on “oh no, I bought a BM/RRA/Stag before I knew better”, all work great together to teach a man to fish. Give them the information, the why AND the how, and let them figure things out for themselves…

By the way. Do we have a list or chart with the known or approx. known gas port sizes of the various makers and configurations out there?

The same thing happens with people working on cars/hotrods guys get greedy thinking that they can run the biggest camshaft in the catalog with stock heads or they try to run a huge carburetor on motor that’s no where capable handling it.
Happens in computers also some body buys a 32x something superburner they install it then it only burns at half the speed the burner is capable of and they think its the burners fault.
I like trying different ways of doing things but I also know what to expect when going out on my own and I don’t freak out the first time it doesn’t work and I also understand that the whole as to work as a system-system-system its all about matching one part to work together with the other part to work as a system.
Sorry about the rambling I have seen it time and time again.:smiley: