I have a LMT receiver with the buffer and Magpuls MS2 mount plate already on and I just recieved the stock and LPK and I was wondering on who you guys think I should send the parts to too have them assembled:
G&R Tactical
ADCO firearms
Do it yourself. It is fairly easy and there is MUCHO info out there as to how it is done.
as IG said, do it yourself. Invest in a rollpin starter punch and a rollpin punch of the size for normal AR roll pins (or a complete set of each – not expensive). It is not hard to do. Find a credible online HOW TO.
You will know how your gun is put together which can be invaluable information to have later and it is fun.
Like the above posters have said it is very easy to do by yourself. Check out this instructional video to help you…
http://www.wonderhowto.com/how-to/video/how-to-build-a-stripped-ar-15-rifle-lower-assembly-255593/
Here is a direct link that you can download and save…
http://www.lifelibertyetc.com/RangeBag/video/LLE_AR15StrippedLower.wmv
Yup, I built mine using the instructional videos. You’ll take more pride in doing it yourself, and learn something in the process.
Its very easy to do. Just watch those ears on the lower when putting the trigger guard roll pin in.
Pin set
Mallet or hammer (I use the midget size one that’s like 6 inches long)
Vise grips (squeeze the bolt catch and trigger guard in place; much easier)
That’s it. $25 in tools. First time took me about 40 minutes. Now I assemble them in 10-12 minutes. Do enough of them you get good at it.
ADCO!
C4
LPK’s are not difficult to install, along with the other links posted Midway has a pretty good one I used to assemble my first lower. It can all be done with a pair of pliers, but a roll pin kit is easier, not too expensive and you run less of a chance of boogering up your lower. Just be careful to get the trigger and hammer springs in correctly, it’s not hard to put them in incorrectly. It took me about a half hour to do my first one and have had no problems with it whatsoever. When it comes time to replace your springs or if a popped primer or something gets stuck in the trigger group you will already be familiar with the trigger group and can clear it yourself. Good luck
the 1st time I installed an LPK I just used an old 1911 firing pin as a tool!
Lower assembly is very easy.
Just make sure everything is lined up right, double and triple check especially on the trigger guard roll pin, rear break down pin spring (it can bend over easily) and bolt catch pin. I use a pair of pliers with duct tape to stop scratches. The pins should slide in evenly if they stop dead part way in its usually misaligned and if you hammer on it you can break an ear off the receiver.
Good Luck!!
Thanks, guys!! I’m gonna go order the tools and give it a shot.
do you have a link for the vise grips?
I prefer this style for small applications. You can get vise-grips at walmart, lowes, home depot, sears, etc…
Someone else mentioned duct tape. I used masking tape, double layered to avoid the sticky mess that duct tape leaves. It was well worth it to protect the lower as the tape was a bit chewed up after my monkey hands got done with the small brass hammer and punch. It was pretty damn easy overall and like has been mentioned, it’ll teach you quite a bit about your rifle. Good luck!
AND shipping to ADCO or G&R will be a bitch since its considered a weapon.
I just finished my first about a month ago, with a piston upper. My suggestion would be to get a set of roll pin punches, they make it much easier. Then go very slow and be careful not to let a punch or pin slip and mar anything up.
I just showed my rifle off, my Brother in law hinted about me building him one, and a friend could not believe how much better it looked than the S&W he purchased last year.
Personally I wrap the jaws in electrical tape. It’s a bit on the thick side and I replace it after each pin as they do chew it up but for me it’s pretty much free as I still have tons of it laying around from the police conversion job I worked 10 years ago.
Good advice above, you’ll do fine with your lower.
I built up my first lower receiver (S&W M&P-15) a couple months ago with no problems. I had a friend who said he’d help but I wanted to do it myself. It’s not hard for anyone who is careful and pays attention to instruction. And I didn’t need any extra tools, just common things many people would have. Brownells has good videos and PDFs on AR assembly so check them out. Their PDFs of the videos are nice since you can have something printed out and right there as you work. They push their own tools but I didn’t need them for one build. But would be handy to have if you were doing many builds.
A few tips that helped me: carefully turn drill bits by hand in the lowers holes to make sure no flash is present; put a drop of oil in the holes and on the pins; use the shank end of the drill bits to help guide trigger, hammer and pivot pins (push out the drill bit with the pin); get a transparant plastic bag to contain the pivot pin detent and spring when installing the pivot pin (so you don’t lose the detent when it goes flying across the room on your first attempt to install); use vise grips with electrical tape around the jaws to install roll pins instead of hammering them in.
My AR turned out great and I’m pleased I had a hand in its assembly. One thing you might see are claims that people put their first receiver together in 15 minutes. Don’t worry about how fast someone else does it, take as long as you need. It took me about 90 minutes (including the buttstock) to have a fully functioning lower receiver. I took my time and thought out things that puzzled me at first, reviewed the videos, etc. until I understood the next step. Maybe I’m slow but there were no mistakes and no idiot marks!
Don’t use vice grips to install roll pins.
Use roll pin starter punches to start and roll pin punches to insert once started.
It is the easiest and most foolproof way to do it and least likely to mar your finish.
Don’t use regular punches.
Also, I find a piece of paperboard like from a cereal box works great to protect the receiver when tapping punches. Just lay it between the pin and the receiver or next to the pin depending on which pin.
But use the right punches.