Anybody use them? I posted this question on another site and found there are a tiny few of us? Pics if you have them.
I bought an M15A2 during the ban, it has an HBar and is very accurate, short of some mag related issues I have had no problems w/ it
I’ve handled and used a few;
really nice fit/finish and accurate too.
too bad the US Dept of State didnt allow me to export one :mad:
…oh well I ended up buying my second Colt ![]()
Ive had several over the years and have been extremely pleased.Right now I have M15A2NM,M15A4 and two Armalite M15A4 uppers living on LMT Defender lowers.All 20" barrels.
Like the others have said the fit and especially the finish on the Armalites is extremely nice.They have about the most durable and consistent finish on the receivers that Ive seen to date.IMHO the overall quality on the parts is excellent and so is accuracy.
The only complaint Ive had recently is the springs and gas rings seem to be a bit weak and will probably need to be replaced almost immediately if you shoot alot.For instance,I had one set of gas rings give up the ghost at about 500 rounds on one of the uppers.
Some folks say the carrier gas keys are not staked properly but all of my have been in the last couple years…and the BCG’s are nicely finished standard quality parts.They are perty anyway.
Otherwise the Armalites respond well to any of the “upgrades” mentioned here on M4C if you feel the need.
I took the advice given by the folks in the know here, and upgraded all the BCG’s to LMT,and replaced all the springs in the lowers.I have to say that going to the LMT BCG’s on the Armalite uppers was purely to please myself in wanting HP/MPI tested parts,which was probably overkill since I seriously doubt I will ever run one of them hard enough to break the factory parts anytime soon.But its worth it to me to have the upgraded parts in place in case I do.
As a side note I have a LMT Defender that Ive setup for 3-gun fun,training and defense purposes.So thats the one I abuse regularly.
To end my ramble I will say Armalite rifles are high quality and excellent performing rifles.If you do the recommended “upgrades” mentioned they are just about as bullet proof as any of the top tier.
My final note is on Armalites customer service.Its outstanding IMHO and they stand behind their products 100%.Some folks may say different,but Armalite has always taken care of me in that regard.
HTH
Forgot to mention.
If you buy a Armalite rifle/20" barrel go ahead and pull the extractor and remove the Crane o-ring.Armalite puts the crane o-ring in all the BCG’s.
If its not removed it can cause some feeding issues on the 20" uppers.Trust me I found out the hard way.
I have the ISP model. It is not a Colt, but it does the job.
Hey, Frens, when did you try the export request? Perhaps with the new guy, you should give it another try. The Colt is nice, but anything for our Italian brothers:)
1 year ago… today both an Italian and Swiss Armalite dealer are unable to export them :rolleyes:
the funny thing is than Bushmaster’s can be exported…it takes time but can be done
![]()
but the weird thing is that an italian importer was able to export a few Colt’s and I didnt even have to fill a “End User” form like I was asked for the Armalite and Bushy.
anyway I’m finally a happy child with my new Pony ![]()
sorry for the hijack
I posted a review [b]here[/b] last year. I recently picked up a mid-length and hope to get a review done after more use. So far it has ran great. However, there were some QC issues. The mag catch was improperly installed (only threaded in a few turns), the pistol grip was improperly installed (again, only threaded in a few turns) and the castle nut looked like it was beat in place with a screwdriver and hammer. No way it should have been shipped like that.
Its possible to see an assembly issue from time to time with just about any manufacturer,and Armalite has theirs too.
One of my most recent Armalite uppers,an M15A4 mentioned above, had a damaged barrel nut from what looked to me the fault of a bad wrench and a heavy hand.Was not a function issue per se,but ugly and not right.I called Armalite and talked with the gunsmith,and he said to send it back that it was not acceptable on one of his guns.I did so and he replaced the barrel nut and had it back to me in a week.
The best advice I can give is if you can,eye ball the rifle,upper etc. extremely well before you buy it.Once you get it home take a better look,clean and test fire…if there is an obvious defect contact the manufacturer and let them deal with it.Fact of the matter is that most of the folks making the better AR’s nowadays stand behind their product 100%.So IMHO customer service should not be an issue especially when it comes to defects and assembly issues.
With that said Ive had excellent customer service from Armalite and LMT,and I highly respect them for it.