Another Kaboom from Arfcom

Does anyone have anything substantive in support of the idea that this was a rifle issue? Or are we just just using this thread to dogpile his low grade DS?

I’m also incredibly skeptical of some of his claims. So, the gun is bone dry, but that’s not because it wasn’t lubed, but because he wiped the oil off? Sorry, but even wiping away oil won’t completely strip it from the metal like that.

It’s also strange how so many failures are a “friend’s” rifle or a “relative’s” rifle.

A local department in my state recently had a 4-year old S&W M&P-15 blow up in a similar fashion, giving one officer a nasty hand injury. No obstructions in the barrel, Smith says the likely culprit was a double-charge in their Federal ammo. Federal has issued a recall for .45 ammo recently, but are mum on this issue so far. My department decided to pull all our fed ammo from our patrol rifles an replace it with Winchester, even though it is a different lot number.

I did not look at the all the pics so it is possible you are right. Headspacing was my first answer.

C4

Most rifle powders for .223/556 you CAN"T double charge it, as most standard (for .223, et al) powders dang near fill the case, or at least up to the shoulders…PISTOL powders, yeah I can see that happening, and it will most likely KABOOM, but not powders intended for .223…

Could have had bullet set back…All other Kb’s I’ve seen split the carrier up at the sides and usually grenades the bolt too. Weird that it only blew out the bottom like that which is indicative that the bolt was locked and in battery when it fired. Could have had the wrong powder.

Haven’t seen it mentioned here, but the OP on TOS followed up that the ammo was PPU (Prvi Partizan).

Todd, I’m in 100% agreement with you, I had two kabooms both with Colts, one Goverment model, and one with a carbine, both back in the 80’s. The pictures look the same as those did, one was traced back reloads without enough crimp on the bullet, causing the bullet to be driven down into the case, thus igniting the charge. The second was factory PMC, but the end result was the same, so either PMC didn’t crimp their ammo or the bullet was shoved into the case durning feeding I don’t know. My magazines in each case were blown apart from the bottom of the mag well to the bottom of the mag (it looked like a barrel that had blown up on a Looney Tunes cartoon) I’m thinking all the remaining ammo was ignited also as we never found any complete rounds only a few melted cases. There was brass residue on the remains of the bolt carrier and bolt, the face-off the bolt was gone and the barrel chamber was brass colored. The upper was severly bulged, and it was the loudest bang I ever heard. My ears rang all day even with ear plugs.

I wonder if Colt would have replaced it if one’s name wasn’t Pat Rogers, but rather John Q. Public?

Rmpl

I have worked on two Colt ARs that “kaboomed.” Same owner, same day, same batch of his reloads. Almost occurred simultaineously as father and son were on line shooting at the same time.

They only bulged the upper receiver on the left side and blew the magazine out.

the best part is no one TOS mentioned that it may be the rifle quality…

thank got for this site and the knowledge is holds, otherwise I would be screwed!

Supposedly it was his first shot of the session.

One thing that sticks out to me is the failed ring and the direction it was pushed.
But then I don’t know if it was tampered with prior to the photo and I’m not sure about the credibility of the “reporter” to even make a guess at the cause.

You can’t double charge a 5.56 case if you are using the correct powder. The second dump would spill out of the case mouth.
Using one of the hotter, correct powders you could over charge a 5.56 and run pressures into the red zone.

I do not believe the Kaboom was caused by the rifles quality. Once the Kaboom occurred the quality of the rifle may have had something to do with the amount of damage that was caused. Regardless of the rifle’s quality it would have sustained severe damage under the pressure that caused that.

Why is that “the best part”? If you have been reading this thread, the folks that know what they are talking about, know that the “quality” or manufacturer, probably has NO bearing on this type of failure.

Lot’s of unsubstantiated conjecture about DS in earlier posts… When my son wanted to build a budge m4gery I researched DS quite a bit. For the record:

  • DoubleStar uses a true 5.56 chamber
  • Can be had with 4150 1:7 chromed barrel, etc. Default is a 4140 with chrome lined as an option. Shaw mfg’d, except the 4150 ones appear to be contract of some form. The FL company with the GI parts contract in Daytona???
  • Lowers are forged 7075 from the same mfg who makes some of the big names (CMMG? CMT?). (yes, I know the lower is immaterial here)
  • Based on the first chart, it actually did pretty well. Including park under FSB, etc. F marked fsb.
  • We did not upgrade the BCG, so it’s a semi without MPI bolt. But we could have upgraded if budget allowed.
  • FCG was decent, better than most clones, but not as clean/crisp as DD/LMT

His is pushing 1k rounds at this point, and has been pretty much flawless. (Yes, he’s a fun shooter. He’ll get his Colt/FN experience at USMA this June). I’m aware of roughly a dozen DS’s friends built, with similar results.

Not to say they are good, or M4C “worthy”… just that I don’t believe for an instant that this kaboom was due to DS. Too many signs point to high pressure. I’d bet barrel obstruction.

No connection to Doublestar, just a satisfied user. It is what it is: a decent budget blaster. I’d buy one in a heartbeat over a Bushy, etc. My last purchase? LMT complete lower, so you know where my priorities are! :slight_smile:

Pretty obvious from the white bolt that that gun has not been properly maintained and oiled.

I noticed a few things looking at the pictures…the weapon was not properly lubed/maintained. Also if you look at picture #2 you can see some of the casing in the chamber. This looks as though there’s a barrel obstruction of some kind. You can see the powder burns on the bolt…this reminds me of the COLT M4’s that went boom on our firing line. Some were caused by human error, i.e. “I forgot the cleaning rod was still in there!” or a squib round & someone didn’t notice it so they fired again. In either event I have seen them where the bolt is in the chamber in the “locked” position after the explosion & I have seen them where the bolt is/was in the rear “unlocked” position. That’s just my input but I wasn’t there & looks can be deceiving!

Here’s some pics of a M4 incident, I know what happened with this one, I was there…






I noticed a few things looking at the pictures…the weapon was not properly lubed/maintained. Also if you look at picture #2 you can see some of the casing in the chamber. This looks as though there’s a barrel obstruction of some kind. You can see the powder burns on the bolt…this reminds me of the COLT M4’s that went boom on our firing line. Some were caused by human error, i.e. “I forgot the cleaning rod was still in there!” or a squib round & someone didn’t notice it so they fired again. In either event I have seen them where the bolt is in the chamber in the “locked” position after the explosion & I have seen them where the bolt is/was in the rear “unlocked” position. That’s just my input but I wasn’t there & looks can be deceiving!

Here’s some pics of a M4 incident, I know what happened with this one, I was there…






I know, I read that article actually. I was just referring to how often you hear about ARs, quality or not over there going tits up. And almost never hear about it on this board.

On TOS I’ve heard of waaaay more Colts, LMT, Noveske, and BCM guns having issues than you hear about on here. I was just making an observation. :p:o

It was November last year, BTW.

ETA: ALWAYS inspect your ammunition by eye, and measure it for setback before you decide to use it…

A lot of folks are bringing up bullet setback, as the possible cause for this type of failure. While that is a very good possibility, we need to realize, that the setback required to cause this kind of pressure, typically occurrs when the bullet hits the feedramp, upon chambering. This would not usually be prevented by inspecting your ammo before loading, as some are suggesting.

A minor set back does not usually produce enough pressure to cause a complete structural failure, as in this case. A setback upon going into the chamber, in which the bullet is severely pushed into the case, and to the extent of being loose, behind the neck, can cause this type of pressure spike. A setback of this nature is usually caused by the tip of the bullet getting hung up, or stopped on something, during chambering. A mismatch between the M4 feedramps of the receiver and barrel extension, in which there is an overhang by the extension, can cause a hangup of this nature. 99.9% of the time, the rounds feed high enough on the ramps, to never catch on this ledge. But, that one in a million round, that the mag doesn’t push quite high enough, and combined with a round that may have a somewhat loose crimp on the bullet, and you may shove that bullet way back into the case, and a kaboom waiting to be touched off.

Folks, this is why I am anal about the match up of the M4 ramps on my guns. An overhang by the extension’s ramp, over the receiver’s ramp, is a no go, as far as I am concerned. Don’t assume for one minute, that the top brands don’t occassionally have this issue. I, have received at least three, probably four, (out of seven I have owned from that company) new uppers, from a top brand manufacturer, that had this condition. Rather than send them back, I simply disassembled the uppers, and properly blended and finished the ramps. DON’T EVEN ASK ME TO REVEAL THE COMPANY, because, no, I did not contact the manufacturer, I simply fixed them myself, which was less hassle and faster for me. I will not mention the company because I don’t want my post deleted, like last time. If you think its a safety issue, then simply check your ramps no matter what brand you have, as any brand is capable of letting a few by, in QC. Some do this simple check, in a few seconds, with a straightened paper clip, to slide the tip of, up the ramps, to see if it catches where the ramps meet.

Would this condition always cause the gun to blow up? Probably never. You have to have the other conditions in place for this to be a real risk (a round fed low, and a less than tight bullet crimp, usually). But, it is a risk, and one that can be avoided by proper ramp matching.

Was this the cause of some of the KB’s seen on the net? Maybe. Squibs, I think less likely, since the AR design would require the squib to land in the very last few inches of the barrel (past the gas port), to cycle that new round on top. Now, if a new round was charged manually, by the shooter, on top of a squib, that was mistakenly perceived as a failure to fire, then yes, very possible. Most KB reports that I have read, the shooter states that they were just firing normally, and don’t mention running the charging handle, after a failure to fire, just prior to the KB.

Just something to think about folks, it only takes a second to check your ramps. I can’t for the life of me, figure why companies don’t pay closer attention to this. I can’t believe how many oppers I have seen with a ramp mesh that could cause a hangup. I take it seriously.