Action block recommendation?

I’ve been using one of the hinged blocks from Bushmaster for some time now and it’s gotten pretty beat up along the way, especially with the latest mess with the vise. To be safe I’d like to replace it but years on I’m no longer so sure it’s the safest way to hold an upper while torquing a barrel nut.

I checked Brownells and the Peace River block they used to sell now says it’s been dropped and there aren’t any others on their site or in their catalog. There’s a two piece affair that can be had through Spikes Tactical but I’m not so sure I’d trust it to avoid warping or twisting a receiver. Other than that I’ve not found much of anything, must be looking in the wrong places I guess. I searched the site here and didn’t find anything using ‘action block’ as the keyword.

Went through gotM4’s tools for AR sticky and have most of 'em (well, not the bolt cutters and pipe wrench anyway) and I noticed the Peace River action block is said to not be used as it leaves marks on the receiver. I’d be really interested in hearing what options there might be instead.

Would definitely appreciate any suggestions or pointers.

TIA, Pete

I use the DPMS one. It’s white with 2 pins and does not “clamp” the entire upper in place. I have used it a couple times already and it’s sufficient enough to torque down a barrel nut.

http://www.bravocompanyusa.com/AR15-DPMS-Panther-Claw-p/panther%20claw%20ar15.htm

dave do you turn it sideways to secure it?I noticed ADCO had some and have though of using it but wasn’t sure if it could withstand the pressure do you have any pictures of the way you did it?? thanks man

It doesn’t say that it was dropped just out of stock. I have used it and it works well. Try putting on backorder.

i’ve literally c-clamped a receiver to a chunk of plywood. ~35fp isn’t that much torque, man. dont sweat it too much.

Huh, never thought of that. It’d work but I’ve seen 60ft-lb or more in a couple of builds. Was sweatin’ it. And DD AR Lite rail barrel nuts can be up to 75ft-lb. I don’t think it’s possible to avoid a warped receiver at that point without a good clamp design but I’m no expert.

Tnx for the idea.

DPMS panther claw.

Nope you just pin the upper in, and crank the vise down on the sides of the plastic block. The entire upper should be above the vise jaws. Really simple to use and leaves no marks on the upper.

I use a Peace River block, a DPMS claw and a PRI block…can’t have enough good tools! :smiley:

Yep, you’re right. I’d originally clicked on the lower receiver block and saw it and what I thought was the upper block were dropped by Brownells but I didn’t read it in detail, it’s the block set that was dropped by Brownells.

Thanks for the help.

Your tools for ARs says something about the Peace River block causing marks on upper receivers, is there a use to avoid because of this?

DPMS Claw’s recommended several times now. How’s it possible for it support the receiver when cranking on a barrel nut?

The PRI block I didn’t know about. So it’s a Claw without the material above the mounting base.

Yeah, I can see how each could be handy for different jobs.

Ever use the action clamp from Bushmaster?

Anyone tried to barrel an upper with the DPMS Flipper?

GTG Thanks that will be the one I go with

DPMS Panther Claw is the way to go. It’s the most versatile too.

Ordered it along with a few other things. Email informs me there will be no backorder and that it as a line item has been cancelled from my order due to it being dropped by Brownells.

Pretty much leaves the Bushmaster action clamp as the only one I know of that fully supports the receiver in the vise.

I use a panther claw as well and have beat the crap out of it and its still holding. :slight_smile:

I too use the DPMS Panther Claw the most. Using the clamp type a shop rag or electrical tape around the receiver will prevent the marks.

All you need is a barrel clamp.

This is the cause of most of the canted FSBs that I repair for people.

You can usually tell when someone has used barrel blocks when installing/removing barrels. If there is aluminum left on the middle of the barrel under the handguards many times if you look closely the FSB is leaning to the shooters right. Ideally it would be best for the upper receiver and the barrel to be secured as the barrel nut is torqued. This would prevent any canting one way or the other.

The only thing I ever use barrel blocks for is for securing the barrel for installation/removal of muzzle devices. I use the non-marring rubber coated barrel blocks from Brownells. I use the solid aluminum ones when securing a barrel in a milling machine when removing/installing perm. mounted flash hiders etc.

I’ve thought this for a long time too. Ever give any thought to trying to mount two vices on the same centerline to try to make it happen? The problem I see is that most vices move only one jaw meaning the centerline changes with the jaw distance and you’d have a different centerline for different barrel profiles.