7.62 x 39 AR

How many here have a 7.62 x39 AR? If so, what magazine do you run?
Thanks

I use ASC 20 rounders and 30 rounders with mine, along with a couple 5 round C-Products mags. The ASC 20 rounders are my favorite. D&H has a 30 round mag that is supposed to be good but I have tried them yet. The ASC’s are a little stiff when loading while new, but this improves with use.

http://ross-zheng-engineering.myshopify.com

Saw this from a link at the NRA Show. An interesting mag for the 7.62x39

Looks good. Pre order only at this time

Are the ASC’s reliable? Is your rifle reliable? I want to do a build on using a Tactical Machining 7.62x39 marked lower, but don’t want to screw up the build with unreliable parts.

My rifle is a complete 16 inch PSA 7.62x39 upper, currently sitting on a DPMS lower with a collapsable M4 type buttstock. I have also tested it with three other lowers that I have that have been verified by me to be reliable: a Smith & Wesson and also a PSA lower, both of which are set up similar to the DPMS with collapsable stocks, with no issues. I have tested it with carbine, H and H2 buffers without issue. I have also tested it with an Anderson lower with a A2 stock and it has been fine.

Really your mag choices are quite limited, at least as far as the ones that I am aware of: there is ASC, C-Products, D&H, and potentially the ones that krm375 posted about. C-Products and ASC appear to be basically the same thing. I have seen reports of a few people having to tweak the feedlips on some of the earlier ASC mags, but I have not found it necessary on my four 20 rounders or two 30 rounders.

Really the only reliability issue I have had so far is ammo related. I have experienced a failure to fire with Tula ammo about one out of every 100 rounds. Normally the casing looks like the primer is set in too deep to allow a good firing pin strike. You can feel and see the bad primers. This is not just a 7.62x39 issue with Tula either, I have seen the same problem with their .223 and 5.45x39 rounds as well. I have found Wolf, Monarch, Silverbear, Hornady and Winchester white box ammo good to go. Your mileage may vary.

Are Tactical Machining 7.62 marked lowers reliable? I have never heard of them.

I can’t say if the Tactical Machining 7.62x39 marked lowers are reliable because I have not built on one yet. I bought three different cartridge marked lowers from them and they all look good. The dimensions I checked were good. I have an anal retentiveness issue, so I don’t like having lowers with the incorrect cartridge designation and don’t care for the multi designation. I ordered upper receivers from them at the same time I purchased my lowers and the finishes all matched perfectly with the lowers. Their prices are very good too. Unfortunately, they don’t stay in stock long, so you have to keep and eye on their website and order promptly.
http://www.tacticalmachining.com/100-receivers/ar15-lower-receivers/7-62x39mm-stripped-lower-receiver.html

So am I correct in understanding that the only things that I’d need to order differently when building my 7.62x39 AR15 are the bolt, barrel and magazines?

CProductsDefense 30rd have been the best in my carbine. ASC 30rd are a bitch to load when new. Will look into the D&H asap.

Yeah, my 30 round ASC mags load ok up to 22 rounds after that they are really difficult, especially once you get to 25 rounds. That is why I said the 20 rounders were my favorite ones.

I’ve got two 7.62x39 ARs, one is an older Alpha Shooting Sports and a new Palmetto State Armory.
I’ve got both the ASC & CPD in 30s & 20s. The springs in the ASCs seemed weak and would occasionally let rounds nosedive. I dropped in AK springs and dremeled out the front of the ASC mags along with the feed ramp til they were reliable. These are four or five year old ASC 30s, newer ones may be better. The ASC 20s are only two years old and had the same problem.

In comparison the CPDs worked correctly the first time with no mods to mag or rifle. Springs are stronger than the stock ASCs and almost as strong as the ASCs with the AK springs, and the finish is much slicker. The CPDs have not malfunctioned in either rifle yet.

Haven’t tried a D&H yet, they have the same profile as the ‘frankenmags’ which seemed to work well. And the D&H mags are supposed to be made of heavy steel. But reviews are hit & miss, some complain of the D&H mags not fitting well with certain lowers, as well as issues with the mag sitting too high and hitting the BCG.

Yes, that should get you where you are going. You may need make sure that your intended muzzle device will work with .30 caliber projectiles and be the proper size and thread pitch for your 7.62 barrel, as well.

Excellent. I knew that about the thread pitch but had forgotten. Thanks for reminding me.

FWIW my first 7.62x39 had a 1/2x36 pitch, same as the one on my RRA 9mm AR. Which is fine for just a flash hider but try to get a 5/8x24 pitch, lets you use standard .308 devices, much better selection. I had to run an adaptor on my first, only source I could find was Primary Weapons Systems. If you buy one of their comps they’ll sell you the adaptor cheap, but just buying the adaptor by itself is pricey.

Thanks for the tip. I’ll definitely stick with the 5/8x24 pitch. Below is a link to a good chart which pretty much spells out the various thread pitch options.
http://www.cncwarrior.com/Muzzle-Devices-s/1822.htm

Tag. These look promising.

Sent from my SM-G900V using Tapatalk

My one ASC mag I bought would jam every round till I spent about 30 minutes slowly dremmeling the front down.
I bought 2 D&Hs and they work alright. They feel solid. I will try buying a couple of CPDs. I have have some original C-Products for the 5.56. Hope they are better than those, cause they are collecting rust now.

I have been patiently waiting for mags to be developed by some of the companies, that have produced multi-caliber carbines.

Sent from my SM-G900V using Tapatalk

These Unimags are available for purchase on the Primary Arms web store: http://www.primaryarms.com/rze-mag-001b/p/rze-mag-001b/.

Here is a quick report from a 7.62x39 user on TOS (note he also shot 6.5 Grendel with equally boring reliability…):

"Ran 200 rounds (8 mags worth at the advertised capacity of 25 rounds for 7.62x39) thru my two Unimags this morning with my YHM 7.62x39 AR.

100% feeding and they locked the bolt open on the last round every time. Perfect function, I am very pleased.

As with every other lower I have tried these mags in (7 lowers total), the Unimags did not drop free in my YHM lower. They did fit somewhat looser in the YHM than the other lowers I have tried them in however.

If there is one round I wanted these Unimags to work with, 7.62x39 is the one. I hate, hate, hate the curvature of conventional 7.62x39 AR mags.

I have knee surgery tomorrow morning, but the plan is to be back at the range on Monday (assuming I’m physically able) to run more 7.62x39 thru these mags. I do not anticipate any issues or drama with these mags.

Finally, a new and truly innovative AR product that lives up to the hype. Gonna buy more of these mags to feed my two Grendels and two 7.62x39 ARs. I’ll probably put my dedicated 6.5 Grendel and 7.62x39 mags in a box and forget about them."

Thanks for the info on the unimag. I ordered on to give it a try.

I’ve seen posts from three different shooters who’ve tried the Unimags with 7.62x39, no complaints.
But $40 a pop. But if you run multiple calibers like I do, may be cheaper in the long run if you can reliably run three or four different calibers from the same mag.
I’m already stocked up on mags but I’m tempted to try one.

Sorry for the long delay, but I have an update on using Unimags in my 7.62x39 Windham AR15. The first one I purchased ran like a champ, not issues at all. So, I bought four more. Unfortunately, none of them would fit in the magazine well of my rifle. In fact, they wouldn’t fit in the magazine well of any receiver. This was odd because the date code on it matched the first individual one that I purchased. I returned them to Primary Arms who paid shipping and gave a prompt refund. I was looking on the Primary Arms website today and found that there is now a generation two version. The difference is that they claim to have solved the magazine well fitting issue. So, I ordered four more. I’ll give them a try and post the results.