308 AR scope mount

What is a good mount for an AR in 308. It wont be going to war or anything and doesn’t need to be QD. I am thinking LaRue SPR mount but that is really the only one I have been exposed to.

What is some other options.

I have a Larue OBR Mount (LT-111) on my 308 rifle.

I have an ADM-H on my 308. it’s beautifully machined and rock solid.
I’m very happy with it.

I put a Nightforce 1-4 on a Larue LT-104 to use on my LMT 308. It looks rock solid.

Have you looked at the Burris PEPR? It’s about $70, or about $90 for the QD version.

My 308s have long enough receivers that I don’t need the PEPR. I bought a PEPR recently and found lock washers under the nuts, not readily removable due to the screws being staked. Lock washers are not appropriate on a scope mount. I have used plain old Burris aluminum rings with good results. They are cheap and effective. I have them on a 375 RUM that kicks hard, I have 400 shots through it, no problem.

The scope mount depends on the scope (eye relief), your preferred cheek position on the stock, and available receiver space.

Based on the above not enough information to answer the question.

It also will depend on how well the dimensions and eye relief of your choice of scope matches the rifle

I’ve used the LaRue LT-104 on numerous builds with a variety of scopes. I don’t think you’ll go wrong with that choice with 95% of the scopes you may opt for.

Just my .02

Saleen

I’m using the American Defense AD-Recon and I’ve been nothing but happy with it.

I would go ADM over Larue. ADM’s approach to locking lugs is superior to that of Larue.

Not sure I would say the ADM locking lugs are superior to LT’s. I have both mounts and think they are both outstanding.

I have the SPR-E on an LMT .556 with a LT rail. I needed the extended mount to get the proper eye relief for my S&B short dot.

On my LMT MWS, I did not need an extended mount because of the monolithic rail. ADM was the only one piece mount that had enough space between the rings for my USO with TPAL side focus.

Basically any Picatinny ring set will work on an AR if you don’t want to go quick release. So your choices are pretty much unlimited. I have used LaRue and ADM with good success. Both are rock solid wrt mounting. Can’t tell you which is better wrt return to zero as I don’t use them that way. Bobro also has a good following, but I have no first had experience. For standard rings I have and very good success with Badger and Seekins rings. LaRue plays in this area as well.

Ring heights and spacing will all depend on your preferred position and scope choice.

Hey All:

Got 2 LMT308MWSE on order and i wanted to ask if a member who has this model might know the entire length of the upper receiver or could measure the entire length of the upper receiver?

Looking at the Dark Ops scope 4-48x56mm for one of the
LMT308MWSE and have not found another scope with these features and magification in a more compact size.

The scope measures to 17 1/2" in length, need to know if it will fit or extend pass the rail?

TIA

I just mounted up on this morning. Nice mount.

I too have an LMT MWS inbound and have been researching a suitable one piece QD scope mount.

I already use several ADM mounts for lights, bipods, and Aimpoints with zero issues, so my first instinct is to go ADM again. However after watching a review on Sniper’s Hide which highlighted some possible issues with return to zero on the ADM I’m not as sure as I initially was.

I know Trident seems to run them with minimal (if any) issue, but for those others of you with experience with the ADM scope mounts, have had any noticeable issues with return to zero?

I don’t intend to frequently remove and remount the optic, but would like the ability to do so without experiencing a dramatic shift in POA vs POI.

I use ADM on both my TR24 and an EOTech riser. Both mounts have come on and off their respective guns many times, mounted back up and never missed a beat.

ADM, Larue, and I’ll throw in a pitch for Bobro. Any of those three will serve you well. There’s been a lot of buzz at snipers hide about another maker called GDI. Those mounts are crazy $$$, though.

There are other answers other than Larue, but they’re probably not better answers. They flat out work. Why experiment?

I use the OBR mount on my 7.62 Noveske. and the OBR mount can fit the USoptics scopes.

How low do you want to mount the scope. How low can you mount it? I would prefer to keep the scope low depending on variables mentioned by others.

I like Larue’s products, but am not sure if they make anything that will go low with some scopes (34mm tubes). ADM makes the Recon-SL mounts which go fairly low (1.19" for a 34mm tube I think). ADM makes good stuff.

Badger Ordnance also makes some one-piece mounts and is apparently providing the mount for GA Precision’s GAP-10 semi-auto rig. I believe it will go down to 1.27".

PS - just read on SnipersHide.com where Larue has come out with a new lower height mount (LT120 - down to 1.285). Might be worth checking as well.

You could just use a riser like Badger Ordnance makes (22 moa built in) or YHM and then use low/medium rings. You could just use high rings meant for ARs, this will probably be the cheapest option.