Teach me about the FAL

[TOrrock]

I just picked this up from a buddy, slightly used....

DSA SA58 Para
18" premium barrel
Standard full length gas system
DSA Type II upper receiver
Aluminum lower receiver
FN M249 grip
DSA Para scope mount
Para bolt carrier with sand cuts
Para folding cocking handle
Buttstock tubes shortened to 9.5"
LOP is now 13.5"
DSA standard handguards
T48 trigger guard
Gemtech Quick Mount flash suppressor
Kahles 1.1-4x CSX illuminated dot scope
LaRue 1.5 qd mount
BFG VCAS sling

I'm going to attach a piece of picatinny rail to the handguards to mount a while light.

[was21]

DMR

I like that topcover.
I replied to your post about it over in the "Files"

Can you shoot me some info on possible availability/cost?
Is this the one that Mark Graham got you hooked up with?

I'm presently using the DSA setup on my carbine but would like to be able to co-witness it.

Thanks
Wes in az

[Cold Zero]

Templar, that is bitchin. Enjoy it.

[ballistic]

DSA SA58 Carbine
DSA Rail Interface Handguard, Tango Down VG and rail panels
DSA Extreme Duty Scope Mount modified for ACOG
Trijicon ACOG TA11C Red Donut calibrated for .308
Para BUIS (sights visible through channel under ACOG)
DSA M249 SAW Pistol Grip

[VooDoo6Actual]

DMR,

Check.

Understood, I'm trying to have my cake and eat it to, since I have all the KIT already.


Otherwise, I might as well put a S&B/NF 1X4 & call it a day.

Could you elucidate who made/makes that mount for you or PM me if you prefer PERSEC.


I would be interested in getting one of those to play with as well.

TIA

[DMR]

DMR,

Check.

Understood, I'm trying to have my cake and eat it to, since I have all the KIT already.


Otherwise, I might as well put a S&B/NF 1X4 & call it a day.

Could you elucidate who made/makes that mount for you or PM me if you prefer PERSEC.


I would be interested in getting one of those to play with as well.

TIA

Negotiations are on going, will be a few weeks before we have the kinks worked out. I doubt I will be the one offering the final product, but it's nice to dream sometimes.

[VooDoo6Actual]

check.

[Cold Zero]

DSA SA58 Carbine
DSA Rail Interface Handguard, Tango Down VG and rail panels
DSA Extreme Duty Scope Mount modified for ACOG
Trijicon ACOG TA11C Red Donut calibrated for .308
Para BUIS (sights visible through channel under ACOG)
DSA M249 SAW Pistol Grip

Very nice build you have there. Who built it for you? Thanks.

[ballistic]

Very nice build you have there. Who built it for you? Thanks.

Thanks CZ. It was a stock SA58 Carbine I bought from DSA c. 1999. I have since upgraded it to the current configuration. I had the standard Extreme Duty scope mount, but the ACOG mounted in an ARMS #19 dual throw lever mount was a bit too high for my liking. The new mount is just right with a much better cheek weld. Other future upgrades planned are an extended safety lever and possibly an alloy lower receiver.

[mark5pt56]

Thanks CZ. It was a stock SA58 Carbine I bought from DSA c. 1999. I have since upgraded it to the current configuration. I had the standard Extreme Duty scope mount, but the ACOG mounted in an ARMS #19 dual throw lever mount was a bit too high for my liking. The new mount is just right with a much better cheek weld. Other future upgrades planned are an extended safety lever and possibly an alloy lower receiver.

Ballistic, Does that Para sight retro the standard rear?

Mark