i stand corrected and im sorry. i manually cycled rounds and it extracted just as you said. i seen how they both work together
Printable View
i stand corrected and im sorry. i manually cycled rounds and it extracted just as you said. i seen how they both work together
I was assuming that a lighter spring and buffer combo would provide less resistance (a lower reciprocating mass), thus compensating for the weaker powered round. Would that not help with the weaker rounds? This could just be a completely ignorant assumption on my part, as I am relatively new to the AR world.
Have you tried switching your buffer spring from your 20yr old Bushy into your DD? Perhaps the spring is more broken in?
Thanks for the suggestions. :)
I have been pretty liberal with my rem-oil; It doesn't seem to help the FTE/cycle issue. It really seems as though it is just not cycling the action enough to eject the round.
Excellent suggestion. I will be taking my rifle to the local gunsmith this week, and having him check/ ream the chamber. I'll post the results asap.
I'm sorry your in the same boat. :P
I am leaning towards trying out JP's Low Mass buffer, and their polished spring. Hopefully this will help as well.
Remoil burns off really, really fast. If you want a cost efficient lubricant that will last on your gun, get some Mobil 1 10w-30 FULL synthetic. CLP and slip 2000 also work well, in my unqualified opinion.
As for your problem, a friend of mine had his front sight walk forward on his Olympic; does it look like your set screws are loose and your front sight could have moved? Cutting off portion of your gas port will definitely stop your rifle from cycling.
The gas pressure gets lower as the bullet goes down the barrel. It may be enough at the carbine gas port position but drop too low at the rifle position of your gas port especially if the powder burn rate is faster than optimal.
Rock River makes a plastic spacer for the 9mm buffer in a rifle stock that I would prefer over quarters. If you reduce the internal length of the rifle buffer tube to that of a carbine it will be perfectly safe to use a CAR buffer and spring.
Remoil is not appropriate lube for an AR, you need something thicker.
Your local gunsmith may not know the difference in .223 and 5.56 chambers, unless he specializes in AR's he will probably just put a headspace gauge in there and call it good.
I want to thank everyone for taking the time to help me with this issue. It's much appreciated.
I had no idea that the rem-oil was crap. I'll check and see if the gunsmith has some of the slip 2000. Fortunately enough, I happen to have some Mobil 1 in the garage. :laugh: Should I use it on the BCG as well?
Strange that you ask, but I think the FSB may be canted to the right (when aiming down the sights) about 1/8 of an inch. I don't think it has set screws though. It looks more like it has pins holding it in place.
You can see in the picture below that the dot on the RMR is to the left of the front sight post.
http://www.hunt101.com/data/500/medium/IMG_03455.jpg
When sighting it in at 25 yards using a Trijicon RMR and an Arms 40 I was experiencing dramatic point of aim/ point of impact differences. (From a bench)
http://www.hunt101.com/data/500/medium/IMG_03397.JPG
The RMR was grouping nicely in the x-ring, whilst the Arms BUIS aperture had to be adjusted all the way to the left for the grouping to the left. They are now almost even on the y-coordinate plane, but significantly off on the x-plane. :sad:
It never occurred to me that this could be causing a partial block of the gas port. Is this likely?
Ah that makes sense. Especially if the canted sight is causing an impediment of the remaining gas pressure flow.
Thank you for the RR spacer tip, I will order one tonight.
I would prefer the rifle to be able to shoot 5.56. The lower receiver is marked "Cal 223 5.56" Should I insist on having it reamed, or just save up for a quality barrel that I know has a 5.56 chamber? I don't want to throw good money after bad. (I see you work for Noveske, and I have been coveting one of your barrels w/a switchblock.)
Thanks again for taking the time to teach me,
S>
Thanks for the tip. I think this will solve the FTE I was having today. I'm going to try this to use up what I have left of wolf military classic. Quoted your tip in a different steel case thread I posted in earlier hope you don't mind. Ammo Thread
Here was my chamber after 500 rds today and two FTE at the end of the day with gunk from the chamber on spent casing.
http://img508.imageshack.us/img508/8518/zoomchamber.jpg
If all else fails remove ur buffer spring and replace it with a colt spring. I had a carbine spring that was 11in. That is in spec but it was too stiff. I bought a dd spring and a bcm spring and my gun cycles tulammo now reliably. I had the same problem the bcg wouldn't retract far enough to pick the next round from the mag. Don't over look a cheap spring it might look good but it can be bad. It happened to me. I'll never buy nothing from delton again.